Plastics reinforced with glass fiber have a significant likelihood of being replaced by natural fiber hybrid composites (NFHCs). Making holes helps in part assembly, which is a crucial activity in the machining of composite constructions. As a result, choosing the right drill bit and cutting parameters is crucial to creating a precise and high-quality hole in composite materials. The present study employs the Taguchi approach to examine the delamination behavior and hole quality of ramie–bamboo composite laminates consisting of epoxy and nano-fillers (SiC, Al2O3) with feed, spindle speed, and three distinct drill bit types. Surface roughness and delamination are significantly influenced by feed and spindle speed, as indicated by the results of the analysis of variance. It was found that the spindle speed had a major impact on the delamination factor and surface roughness, while the feed and drill bit type had a minor influence. The surface roughness (76.5%) and delamination factor (66.7%) are significantly affected by the spindle speed.
The study explores the mechanical and morphological studies of ramie, bamboo, and hybrid ramie-bamboo composites with silicon carbide (SiC) and alumina (Al2O3) nano-fillers. The composites were fabricated using the hand-layup method followed by compression moulding. Mechanical characteristics such as tensile, flexural, impact, and hardness were investigated as per the ASTM standards. Surface characterization was performed using scanning electron microscopy (SEM) to understand the surface characteristics and failure behavior of composites. Experimental results indicated that the maximum tensile strength (50.16 MPa), impact strength (6.30 kJ m−2), and hardness (79.4) were obtained for the ramie-bamboo hybrid composite, while the pure ramie composite exhibited the greatest flexural strength (101.4 MPa). SEM analysis revealed good fiber-matrix bonding within the hybrid composites. Ramie-bamboo hybrid composites with nano-fillers showed lower strength values due to the agglomeration of nano-fillers. The present findings provide insight into optimizing hybrid natural fiber composites for enhanced mechanical performance.
Fibre-reinforced polymer composites incorporating synthetic reinforcements such as glass and carbon fibres are widely used due to their superior mechanical performance. However, their energy-intensive production and end-of-life disposal contribute to an increased carbon footprint and significant environmental burden. Natural fibre-reinforced composites have emerged as promising low impact alternatives, but variability in their mechanical performance and the lack of controlled comparative studies limit their structural application. This study presents a controlled experimental comparison of alkaline-treated unidirectional flax/epoxy and hemp/epoxy composites fabricated using the vacuum-assisted resin infusion moulding (VARIM) process. Alkali treatment was employed to enhance the fibre–matrix interfacial bonding. Mechanical characterization was conducted through tensile, flexural, impact, interlaminar shear strength (ILSS), and Vickers microhardness testing in accordance with relevant ASTM and ISO standards. The flax/epoxy composites exhibited superior in-plane mechanical performance including, 9.1% higher tensile modulus, 13.8% higher flexural strength and 20.5% higher flexural modulus compared to hemp/epoxy composites. A significant improvement was observed in impact performance, with hemp composites showing 87.4% higher impact strength, indicating enhanced resistance to dynamic loading. Conversely, hemp/epoxy composites demonstrated a 10.6% higher ILSS, suggesting improved interfacial shear resistance and fibre interlocking. These findings confirm that the fibre type significantly influences composite performance, with flax fibres providing superior stiffness and strength, while hemp fibres offer better interlaminar shear behaviour and impact strength. Scanning Electron Microscopy (SEM) fractographic analysis was additionally conducted on fracture surfaces to characterize failure mechanisms and fibre–matrix interfacial morphology. The present study provides a reliable comparative framework for material selection and demonstrates the potential of flax- and hemp-based composites as sustainable alternatives for lightweight structural applications. This study supports the development of sustainable composite materials and contributes to the United Nations Sustainable Development Goals (SDGs), particularly SDG 12 (Responsible Consumption and Production), SDG 13 (Climate Action), and SDG 11 (Sustainable Cities and Communities).
Carbon fiber-reinforced polymer (CFRP) composites modified with alumina (Al2O3) and silicon carbide (SiC) nanoparticles were developed to produce hybrid nanocomposites with improved mechanical and thermal characteristics. This study investigates the hot drilling behavior of unidirectional CFRP and hybrid nanocomposites by examining the effects of spindle speed, feed rate, drill diameter, and drill geometry (step, core, and twist). Response Surface Methodology (RSM) and Analysis of Variance (ANOVA) were used to identify the most influential parameters governing drilling-induced damage. ANOVA results revealed that drill geometry was the most dominant factor, contributing more than 89% to delamination, burr formation, and surface roughness, followed by drill diameter with over 7% contribution. For temperature rise, drill geometry accounted for more than 50% of the total variation, while drill diameter contributed over 17%. Among the tools evaluated, the step drill produced the minimum drilling-induced damage, followed by the twist drill. In terms of material performance, the Al2O3-reinforced hybrid nanocomposite exhibited superior drilling behavior compared to the SiC-reinforced and neat CFRP laminates. Overall, the results demonstrate that drilling-induced damage under hot drilling conditions can be effectively minimized through appropriate selection of tool geometry and process parameters, confirming the suitability of hot drilling for machining aerospace-grade CFRP hybrid nanocomposites.