Valentyn Veis

Valentyn Veis

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 August 2025 in Steel Research International
Verified
Journal Article
Closed access
VVValentyn Veis
Valentyn Veis
Anastasiia SemenkoAnastasiia Semenko
Anastasiia Semenko
MVMykhailo Voron
Mykhailo Voron
ATAndrii Tymoshenko
Andrii Tymoshenko
RLRichard Likhatskyi
Richard Likhatskyi
ZPZhanna Parkhomchuk
Zhanna Parkhomchuk

20 December 2018 in Metaloznavstvo ta obrobka metalìv
Verified
Journal Article
Open access
SKS.Ye. Kondratyuk
S.Ye. Kondratyuk
ZPZhanna Parkhomchuk
Zhanna Parkhomchuk
VVValentyn Veis
Valentyn Veis

30 September 2018 in Metaloznavstvo ta obrobka metalìv
Verified
Journal Article
Open access
SKS. Ye. Kondratyuk
S. Ye. Kondratyuk
VSV. M. Shcheglov
V. M. Shcheglov
VVValentyn Veis
Valentyn Veis

28 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
Alexander BalitskiiAlexander Balitskii
Alexander Balitskii
YKYulia H. Kvasnytska
Yulia H. Kvasnytska
Ivaskevych M LjubomyrIvaskevych M Ljubomyr
Ivaskevych M Ljubomyr
Kateryna KvasnytskaKateryna Kvasnytska
Kateryna Kvasnytska
OBOlexiy Balitskii
Olexiy Balitskii
JDJakub Dowejko
Jakub Dowejko
This paper presents the results of an analysis of resistance to hydrogen embrittlement and offers solutions and technologies for manufacturing castings of components for critical applications, such as blades for gas turbine engines (GTEs). The values of the technological parameters for directional crystallization (DC) are determined, allowing the production of castings with a regular dendritic structure of the crystallization front in the range of 10 to 12 mm/min and a temperature gradient at the crystallization front in the range of 165–175 °C/cm. The technological process of making GTE blades has been improved by using a scheme for obtaining disposable models of complex profile castings with the use of 3D printing for the manufacture of ceramic molds. The ceramic mold is obtained through an environmentally friendly technology using water-based binders. Short-term tensile testing of the samples in gaseous hydrogen revealed high hydrogen resistance of the CM-88 alloy produced by directed crystallization technology: the relative elongation in hydrogen at a pressure of 30 MPa increased from 2% for the commercial alloy to 8% for the experimental single-crystal alloy.

20 December 2021 in Metaloznavstvo ta obrobka metalìv
Verified
Journal Article
Open access
SKS.Ye. Kondratyuk
S.Ye. Kondratyuk
VVValentyn Veis
Valentyn Veis
ZPZhanna Parkhomchuk
Zhanna Parkhomchuk
VLV.A. Loktyonov-Remyzovskii
V.A. Loktyonov-Remyzovskii
The effect of overheating of the melt over the equilibrium liquidus in the temperature range 1570 °C – 1670 °C and the rate of its cooling during crystallization and structure formation of castings on the formation of the length and morphology of the main macrostructural zones, grain dispersion, characteristics of the fine crystal structure, hardness and intensity of abrasive wear over the section of 25L steel castings with a differentiated cast structure was investigated. Regular changes of these indicators depending on thermokinetic conditions of crystallization are established. The determining influence of the melt cooling rate on the morphology and dispersion of the cast structure due to different degrees of melt supercooling during crystallization of different structural zones of castings is shown. As the distance from the rapidly cooling surface of the castings and taking into account the increase in the temperature of the melt overheat from 1570 ºC to 1670 ºC, the grain size varies from 5… 7 numbers to 1… 2 numbers, respectively. In the case of normal heat removal rate during crystallization, the grain size in the castings varies from 4… 2 to -1… -2 numbers. The determined characteristics of wear resistance of steel in different structural zones correlate with changes in the characteristics of the cast structure and the cross-sectional strength of castings. The research results open the prospect of developing new foundry technologies for the production of cast products with differential properties for special operating conditions. Keywords: gradient structure, structural zones, melt, wear.

30 September 2021 in Metaloznavstvo ta obrobka metalìv
Verified
Journal Article
Open access
SKS.Ye. Kondratyuk
S.Ye. Kondratyuk
VVValentyn Veis
Valentyn Veis
ZPZhanna Parkhomchuk
Zhanna Parkhomchuk
GSG.I. Shevchenko
G.I. Shevchenko
The influence of melt overheating in the range of 50-150 °C on the equilibrium liquidus and its cooling rate during crystallization of castings on the formation of macrostructural zones along their cross section, on the change of grain dispersion, dendritic structure characteristics and mechanical properties was investigated on the example of 25L steel. It is established that the macrostructure of castings in the direction of unilateral heat removal as it moves away from the cooled surface consists of four main structural zones - small coaxial crystals, columnar, branched and large coaxial crystals, the length and morphology of which naturally change depending on thermokinetic conditions of crystallization. The decisive role of the cooling rate at significant overheating of the melt to increase the number of crystallization nuclei, the formation of a more dispersed cast structure by increasing the degree of supercooling of the melt during crystallization is shown. The regularities of quantitative characteristics change of microstructure and dendritic structure depending on change of temperature-time parameters of crystallization in different structural zones of castings and their connection with characteristics of mechanical properties of steel are established. On the basis of mathematical processing of experimental data by linear regression analysis interpolation models and their graphical interpretations are obtained, which allow to quantify and predict the change of mechanical properties in different structural zones of gradient castings depending on melt overheating temperature and cooling modes within the investigated factor space. Keywords: gradient structure, structural zones, melt, mechanical properties.