Dogan Sinar

Dr. Dogan Sinar


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 July 2020 in IEEE Sensors Journal
Verified
Journal Article
Closed access
DSDogan Sinar
Dogan Sinar
GMGabriel Junquetti Mattos
Gabriel Junquetti Mattos
George KnopfGeorge Knopf
George Knopf
Significant fluctuations in body fluid pH can indicate the onset of infection or a chronic condition. In this paper, a hydrogel-activated circular discrete interdigitated capacitive (D-IDC) biosensor is introduced for monitoring the acidity of biological fluids. The pH-sensitive transducer is a thin biocompatible chitosan / polyvinyl alcohol hydrogel disk positioned at the center of a multi-terminal D-IDC comprised of numerous distinct circular conductive electrodes covering the active sensing area. The D-IDC is printed on Nylon-66 filter paper that has been coated with a thin layer of polydimethylsiloxane (PDMS). The circular electrode pattern is printed on the PDMS surface using nontoxic graphene / carboxymethyl cellulose (G-CMC) aqueous suspensions as the electrically conductive ink. A thin polymer passivation layer is then spin coated on the surface of the G-CMC conductive electrodes to prevent an electrical short with the liquid filled hydrogel transducer. The pH level of the fluid causes the centrally located hydrogel transducer to swell/de-swell over the circular electrodes producing an incremental change in the measured capacitance. A prototype comprised of seven electrode pairs is fabricated and experimentally tested under controlled conditions using phosphate buffer solutions (PBS) with varying pH. The operational and analytical parameters of the hydrogel-activated biosensor are evaluated in terms of measured capacitance. The prototype sensor demonstrates acceptable repeatability (SD < 0.4%) and reproducibility (SD < 5.8%). Sensor resolution can be modified by reducing the physical size of the electrode micro-traces used in the D-IDC design and increasing the number electrode pairs.

20 June 2018 in IEEE Transactions on Nanotechnology
Verified
Journal Article
Open access
DSDogan Sinar
Dogan Sinar
George KnopfGeorge Knopf
George Knopf
Advances in electrically conductive inks and printing technology have enabled microelectrodes, chemical sensors, wireless radio frequency identification tags, and bioelectronic circuits to be fabricated on mechanically flexible polymers, paper, and bioresorbable silk. Although conductive polymer and metal-based inks have been used to build functional devices, these materials are often expensive and may involve complicated toxic chemical processes. Recent research has demonstrated that graphene (G), and its derivatives, can be used to create water-based conductive inks. In this paper, an environmentally friendly and cost-effective G-based conductive ink is proposed. The ink is created by using a nontoxic hydrophilic cellulose derivative, Carboxymethyl Cellulose (CMC), to facilitate liquid phase exfoliation and stabilization of naturally hydrophobic G sheets in DI water at high concentrations. It is demonstrated that recycling of nonexfoliated material can produce inks at comparable concentrations. Physical dimensions and defect status of exfoliated G sheets are characterized. Inkjet deposition of thin and thick films is achieved using a binary solvent system and electrical performance of resulting films is investigated. Film morphology is shown to be consistent between thin and thick films. Experiments have demonstrated that G-CMC films of <;700 Ω/sq can be inkjet printed without use of dopants or dangerous solvents.

23 February 2018 in Nanomaterials
Verified
Journal Article
Open access
PDF file
DSDogan Sinar
Dogan Sinar
George KnopfGeorge Knopf
George Knopf
The objective of this study is to inkjet print resistor-capacitor (RC) low pass electrical filters, using a novel water-based cellulose graphene ink, and compare the voltage-frequency and transient behavior to equivalent circuits constructed from discrete passive components. The synthesized non-toxic graphene-carboxymethyl cellulose (G-CMC) ink is deposited on mechanically flexible polyimide substrates using a customized printer that dispenses functionalized aqueous solutions. The design of the printed first-order and second-order low-pass RC filters incorporate resistive traces and interdigitated capacitors. Low pass filter characteristics, such as time constant, cut-off frequency and roll-off rate, are determined for comparative analysis. Experiments demonstrate that for low frequency applications (<100 kHz) the printed graphene derivative circuits performed as well as the circuits constructed from discrete resistors and capacitors for both low pass filter and RC integrator applications. The impact of mechanical stress due to bending on the electrical performance of the flexible printed circuits is also investigated.

16 February 2017
Verified
Conference Paper
Closed access
PDF file
DSDogan Sinar
Dogan Sinar
GKGeorge K. Knopf
George K. Knopf
SNSuwas Nikumb
Suwas Nikumb

1 January 2022
Verified
Conference Paper
Closed access
PDF file
RTRamy Tannous
Ramy Tannous
WWWilson Wu
Wilson Wu
SVStephane Vinet
Stephane Vinet
CPChithrabhanu Perumangatt
Chithrabhanu Perumangatt
DSDogan Sinar
Dogan Sinar
TJThomas Jennewein
Thomas Jennewein
We present the experimental results of the first reference frame independent time bin quantum key distribution. Despite a lack of active phase stabilization of the interferometers, 0.078 asymptotic secret key bits per second were generated.