Dyes are frequently used in industries such as textile, leather, paper and printing, to water sources causes harmful effects on the environment and human health. Therefore, it is crucial to effectively remove colored contaminants from water in order to protect the environment and public health, maintain biodiversity and preserve the esthetic aspects of water resources. In this study, wood chips obtained from Pinus brutia (PB) tree grown in many parts of the world were turned into biochar and then modified and used for the removal of malachite green, a cationic dye. For this purpose, biochar (PBB) was made by collecting PB wood and turning it into chips (PB). Later, PBB was modified to gain nano-magnetic properties. The structure of the obtained PBB and nM-PBB adsorbents was characterized by FT-IR. pH (2-9), temperature (25 °C-55 °C), time change (15 min-240 min), adsorbent amount change (0.05 g-0.45g) and MG concentration (25 mg/L-250 mg/L) were investigated in MG removal of PBB and nM-PBB. The process was found to be pseudo-second-order and spontaneous endothermic reaction. PBB and nM-PBB were found to be suitable for Langmuir isotherm in MG removal (qmax=13.004 mg/g for PBB, qmax=18.215 mg/g for nM-PBB).
2 April 2025 in Biomass Conversion and Biorefinery
The use of biochar, which is a carbon-rich material obtained by pyrolysis of various organic raw materials for dye pollution in wastewater, is promising for the removal of dyes from wastewater. Modified biochars whose structures are changed are currently being investigated with many studies. In this study, Juniperus Excelsa (JE) cone, which is an economical and accessible tree species, was converted into biochar (JEB) and modified with iron (mJEB) and given magnetic properties. mJEB was characterized and its structure was investigated by Brunauer–Emmett–Teller (BET), X-Ray diffraction method (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and point of zero charge (pHPZC). Afterwards, the removal of malachite green (MG) dye by batch adsorption method was investigated in adsorption parameters such as pH, temperature, time, dosage, initial MG concentration. The results showed that MG adsorption with mJEB proceeded via pseudo-second-order (PSO), was an endothermic process and complied with the Langmuir isotherm model. The maximum adsorption capacity (qmax) in MG removal with mJEB was calculated as 38.023 mg/g. Our study will be an important step in dye removal studies with mJEB. Graphical Abstract
12 April 2024 in Journal of Dispersion Science and Technology
1. Clean water is one of the important aspects of life. As a result of industrial developments, the amount of accessible water is gradually decreasing. Therefore, strict environmental regulations m...
In this study, we conducted a novel method by using a household type Microwave Owen (MW) under selected operational parameters (power and time) to treat wastewater from paper recycling under laboratory conditions. We seek to evaluate changes of the MW experimental parameters, comparatively. All measured pH values were found to be in very narrow range, between pH 7.10 (BII) and pH 7.53 (DIV), in slightly alkaline range (>7.0). However, the highest Electrical Conductivity (EC) difference was found to be 46 µS/cm. The 60 seconds MW irradiated samples at four power levels (90-, 180-, 270-, 360 Watts) showed higher ORP values than control (C1: 195 mV) while the highest ORP value of 213 mV was found with sample treated 360 W and 60 seconds (DIV). It is notable that sample DIV showed the highest pH, EC, ORP and TDS value. The control sample had turbidity value of 42.5 NTU. In all MW power levels and durations, turbidity removal was apparent which MW impact on turbidity. The lowest turbidity value of 22.2 NTU was found with sample DIV which was the highest rate of turbidity removal efficiency (DIV: 86.2%). The present study revealed that MW irradiation could be used to effectively reduce the selected physicochemical parameters that may assist in the description of wastewater quality.