Jens Von Wolfersdorf

Prof. Dr. Jens Von Wolfersdorf


Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2004 in Heat and Mass Transfer
Verified
Journal Article
Closed access
PDF file
JWJens Von Wolfersdorf
Jens Von Wolfersdorf

21 February 2012 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
JKJoachim Karnahl
Joachim Karnahl
JWJens Von Wolfersdorf
Jens Von Wolfersdorf
KTKok-Mun Tham
Kok-Mun Tham
MWMike Wilson
Mike Wilson
GLGary Lock
Gary Lock
This paper presents computational fluid dynamics (CFD) predictions of flow and heat transfer for an over-swirled low-radius preswirl system and comparison with experimental data. The rotor-stator CFD model comprises a stationary domain with the preswirl nozzles and a rotating domain with the receiver holes. The fluid-dynamic conditions feature an over-swirled system with a swirl ratio at the nozzle radius βp = 1.4−1.5 and rotational Reynolds number ReΦ = 0.8 × 106 and 1.2 × 106. Three different treatments for the rotating and stationary domain interface are used to evaluate the influence on the flow and heat transfer behavior: a stationary approach (including Coriolis forces in the rotating domain) with “direct connection” and fixed angle between preswirl nozzle and receiver holes; a stationary approach with circumferential averaging of the velocity at radial bands; and a full transient simulation with the rotating domain capturing the unsteady flow due to the rotating receiver holes. Results at different circumferential angles show high variability in pressure and velocity distributions at the preswirl inlet nozzle radius. Circumferential averaging of these flow parameters lead to an alignment of the pressures and velocities between the three different interface approaches. Comparison with experimental pressure and swirl-ratio data show a quantitative agreement but the CFD results feature a systematic overestimation outward of the preswirl nozzle radius. Heat transfer coefficient distributions at the rotor surface show the effect of the different interface approaches and dependence on the flow structure (for example the impinging jet and vortex structures). The three different interface approaches result in significant differences in the computed heat transfer coefficients between pairs of receiver holes. Circumferentially averaged heat transfer coefficients inward of the receiver holes radius show good agreement between the transient and stationary direct connection interfaces, whereas those for the circumferential averaging interface differ, contrary to the flow parameters, due to smoothing of local effects from the preswirl jets.

28 September 2014 in Experimental Thermal and Fluid Science
Verified
Journal Article
Closed access
ATAlexandros Terzis
Alexandros Terzis
JWJens Von Wolfersdorf
Jens Von Wolfersdorf
BWBernhard Weigand
Bernhard Weigand
POPeter Ott
Peter Ott

1 January 2005
Verified
Conference Paper
Closed access
PDF file
RPRico Poser
Rico Poser
JWJens Von Wolfersdorf
Jens Von Wolfersdorf
KSKlaus Semmler
Klaus Semmler
Transient heat transfer experiments were performed in a model of a multi-pass gas turbine blade cooling circuit. The inner surface of the Plexiglas model was coated with thermochromic liquid crystals in order to determine the internal heat transfer coefficients. A change in inlet temperature is applied using a pre-cooled heat exchanger. As for simple geometries the analytical solution of Fourier’s equation can often be directly used for data evaluation, one ought to pay attention to complex passages. The reason has to be seen that the flow in complex passages has to be characterized by local and time dependent fluid temperatures. As a direct consequence data evaluation might be limited to small evaluation areas especially far downstream. Otherwise the uncertainties in the heat transfer results will increase substantially. In the present study the sensitivity of the transient method for complex passages has been analyzed theoretically and applied experimentally.

CHChristopher Hartmann
Christopher Hartmann
JSJulia Schweikert
Julia Schweikert
FCFrançois Cottier
François Cottier
UIUte Israel
Ute Israel
JGJochen Gier
Jochen Gier
JWJens Von Wolfersdorf
Jens Von Wolfersdorf
Experimental results for the transient heat transfer characteristics over a flat plate and over a plate with V-shaped ribs were compared to numerical results from a coupling environment applying FEM and CFD. In order to simulate transient effects in the cooling process of engine components during typical flight missions, the temperature and the velocity at the inlet of the channel were varied over time. The transient temperature distribution at the plate was measured using infrared thermography. Five different plate materials (perspex, PEEK, quartz, aluminum, and steel) were considered to investigate the influence of thermal conduction on the heat transfer between solid and fluid depending on the Biot number. The experimental results represent a reference database for a Python-based coupling environment applying CalculiX (FEM) and ANSYS CFX (CFD). The results were additionally compared to numerical results simulating the complete transient conjugated heat transfer with CFD. A good agreement between the numerical and the experimental results was achieved using different coupling sizes at different Biot numbers for the flat plate and the plate with V-shaped ribs.

30 November 2004 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
DCD. Chanteloup
D. Chanteloup
JWJens Von Wolfersdorf
Jens Von Wolfersdorf