Rico Poser

Dr. Rico Poser

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 April 2024 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
MFMarius Forster
Marius Forster
PLPhillip Ligrani
Phillip Ligrani
BWBernhard Weigand
Bernhard Weigand
RPRico Poser
Rico Poser

6 December 2022 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Open access
TKTobias Krille
Tobias Krille
RPRico Poser
Rico Poser
JWJens von Wolfersdorf
Jens von Wolfersdorf
MHMarc Henze
Marc Henze

1 February 2023 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
JHJulian Härter
Julian Härter
DMDavid Sebastian Martinez
David Sebastian Martinez
RPRico Poser
Rico Poser
BWBernhard Weigand
Bernhard Weigand
GLGrazia Lamanna
Grazia Lamanna
The existence of large-scale turbulent structures within a porous medium, generated through the interaction with a turbulent outer flow, is a highly debated topic, albeit most of the analysis is based on computational studies. This study contributes to the ongoing discussion by providing detailed point-measurements of the velocity in both regions by means of Particle Image Velocimetry (PIV). Two porous models of different porosity are investigated at three Reynolds numbers. The design of the experiments is based on theoretical studies to guarantee the presence of an unperturbed viscous layer at the interface (alias permeability Reynolds numbers of order one). Under these conditions and in compliance with theoretical predictions, the PIV data show the rapid dumping of turbulent fluctuations within the first pore cavities and can be used to validate closure models for volume-averaged computational studies. A point-data analysis is applied in the interfacial region by requiring continuity of tangential velocity and shear stress. The presence of the attached viscous layer implies that the coupling condition for momentum transfer must be controlled by shear, leading to the well-known Beavers and Joseph coupling condition. PIV data corroborate this statement and show the close interdependency between the penetration depth of the outer flow in the porous media and the characteristics of the vortical secondary flows induced by the strain rate at the pore scale. Consequently, the Beavers and Joseph-slip coefficient depends only upon the topology of the porous medium, at least as long as no transition to a perturbed mixing layer occurs at the interface.

1 January 2005
Verified
Conference Paper
Closed access
PDF file
RPRico Poser
Rico Poser
JWJens Von Wolfersdorf
Jens Von Wolfersdorf
KSKlaus Semmler
Klaus Semmler
Transient heat transfer experiments were performed in a model of a multi-pass gas turbine blade cooling circuit. The inner surface of the Plexiglas model was coated with thermochromic liquid crystals in order to determine the internal heat transfer coefficients. A change in inlet temperature is applied using a pre-cooled heat exchanger. As for simple geometries the analytical solution of Fourier’s equation can often be directly used for data evaluation, one ought to pay attention to complex passages. The reason has to be seen that the flow in complex passages has to be characterized by local and time dependent fluid temperatures. As a direct consequence data evaluation might be limited to small evaluation areas especially far downstream. Otherwise the uncertainties in the heat transfer results will increase substantially. In the present study the sensitivity of the transient method for complex passages has been analyzed theoretically and applied experimentally.

25 May 2023 in Applied Thermal Engineering
Verified
Journal Article
Closed access
FSFlorian Seibold
Florian Seibold
PLPhillip Ligrani
Phillip Ligrani
XYXing Yang
Xing Yang
RPRico Poser
Rico Poser
BWBernhard Weigand
Bernhard Weigand

DADavid Gutiérrez de Arcos
David Gutiérrez de Arcos
CWChristian Waidmann
Christian Waidmann
RPRico Poser
Rico Poser
JWJens von Wolfersdorf
Jens von Wolfersdorf
MGMichael Göhring
Michael Göhring
Turbine blades for modern turbomachinery applications often exhibit complex twisted designs that aim to reduce aerodynamic losses, thereby improving the overall machine performance. This results in intricate internal cooling configurations that change their spanwise orientation with respect to the rotational axis. In the present study, the local heat transfer in a generic two-pass turbine cooling channel is investigated under engine-similar rotating conditions (Ro={0…0.50}) through the transient Thermochromic Liquid Crystal (TLC) measurement technique. Three different angles of attack (α={−18.5°;+8°;+46.5°}) are investigated to emulate the heat transfer characteristics in an internal cooling channel of a real turbine blade application at different spanwise positions. A numerical approach based on steady-state Reynolds-averaged Navier–Stokes (RANS) simulations in ANSYS CFX is validated against the experimental method, showing generally good agreement and, thus, qualifying for future heat transfer predictions. Experimental and numerical data clearly demonstrate the substantial impact of the angle of attack on the local heat transfer structure, especially for the radially outward flow of the first passage, owing to the particular Coriolis force direction at each angle of attack. Furthermore, results underscore the strong influence of the rotational speed on the overall heat transfer level, with an enhancement effect for the radially outward flow (first passage) and a reduction effect for the radially inward flow (second passage).