Energy Autonomous Wearable Sensors (EAWS) have attracted a large interest due to their potential to provide reliable measurements and continuous bioelectric signals, which help to reduce health risk factors early on, ongoing assessment for disease prevention, and maintaining optimum, lifelong health quality. This review paper presents recent developments and state-of-the-art research related to three critical elements that enable an EAWS. The first element is wearable sensors, which monitor human body physiological signals and activities. Emphasis is given on explaining different types of transduction mechanisms presented, and emerging materials and fabrication techniques. The second element is the flexible and wearable energy storage device to drive low-power electronics and the software needed for automatic detection of unstable physiological parameters. The third is the flexible and stretchable energy harvesting module to recharge batteries for continuous operation of wearable sensors. We conclude by discussing some of the technical challenges in realizing energy-autonomous wearable sensing technologies and possible solutions for overcoming them.

Controlling properties of one-dimensional (1D) semiconducting nanostructures is essential for the advancement of electronic devices. In this work, we present a low-temperature hydrothermal growth process enabling density control of aligned high aspect ratio ZnO nanowires (NWs) on seedless Au surface. A two order of magnitude change in ZnO NW density is demonstrated via careful control of the ammonium hydroxide concentration (NH₄OH) in the solution. Based on the experimental observations, we further, hypothesized the growth mechanism leading to the density controlled growth of ZnO NWs. Moreover, the effect of NH₄OH on the electrical properties of ZnO NWs, such as doping and field-effect mobility, is thoroughly investigated by fabricating single nanowire field-effect transistors. The electrical study shows the increase of free charge density while decrease of mobility in ZnO NWs with the increase of NH₄OH concentration in the growth solution. These findings show that NH₄OH can be used for simultaneous tuning of the NW density and electrical properties of the ZnO NWs grown by hydrothermal approach. The present work will guide the engineers and researchers to produce low-temperature density controlled aligned 1D ZnO NWs over wide range of substrates, including plastics, with tunable electrical properties.

Using vertically grown hydrothermal ZnO nanowires, we demonstrate the assembly of fully functional piezoelectric energy harvesters on plastics substrates. A seedless hydrothermal process is employed for the growth of single crystalline vertically orientated ZnO NWs at around 100oC. Flexible NG are assembled using ∼7μm thick PDMS polymer matrix on a 3x3cm substrate. A representative device with an active area of 4cm2 is characterised revealing average output voltage generation of ∼22mV (±1.2) and -32mV (±0.16) in the positive and negative cycles after 3-4mm periodic deflection at 20Hz. A power density of ∼288nW/cm3 is estimated for the device. It is envisaged that such energy scavengers may find potential applications targeting self-powered systems, sensors and on-body charging of electronics

The present work demonstrates the production of single crystalline ZnO nanowires (NWs) using the low temperature hydrothermal process and their integration as the active channel material and piezoelectric elements in single NW field-effect transistors (FETs) and functional nanogenerators (NGs), respectively. Even though hydrothermally grown ZnO NWs show high levels of excess free carriers ≫10¹⁸ cm⁻³, we show that an optimized thermal annealing process at just 450 °C in atmospheric air sufficiently reduces this level to around ∼3.7 × 10¹⁷ cm⁻³. The excess free carrier suppression is verified by assessing the field-effect transport behaviour in a single NW FET. The single device is found to exhibit good performance metrics, including low off-state current (pA range), high on-state current (in the 10 s of μA range) and moderate effective mobility (∼10 cm² V⁻¹ s⁻¹). The functional NGs are based on vertically grown ZnO NWs with ∼7 μm thick polydimethylsiloxane (PDMS) polymer matrix. We show that a NG incorporating annealed ZnO NWs can continuously generate higher output voltages and power compared to a reference device based on as-grown ZnO NWs. This included peak output voltage of ∼109 mV and an output power density of ∼16 μW cm⁻³. We envisage that this approach of thermal annealing may find practical applications in other areas of hydrothermal ZnO NW research, including high performance NW FETs and piezoelectric energy harvesters.