FRANCO J S SILVA

Dr. FRANCO J S SILVA

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2016 in Journal of Quality in Maintenance Engineering
Verified
Journal Article
Closed access
FSFRANCO J S SILVA
FRANCO J S SILVA
HVHerbert Ricardo Garcia Viana
Herbert Ricardo Garcia Viana
AQAndré Nasser Aquino Queiroz
André Nasser Aquino Queiroz
The purpose of this paper is to present a methodology for forecasting the availability off-highway trucks used in a fleet for large transport operations of ore and sterile rock from an open pit mine. This methodology enables the estimation of the number of hours of preventive and corrective maintenance required, which are used to predict truck availability. The authors used historical data for the maintenance strategy based on the hours of operation. These data are statistically analyzed to obtain the key quantities and statistical models required to project availability and to develop equipment replacement plans. A methodology for forecasting availability to assets in open pit mining industry was implemented.

16 September 2025 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
ALAntonio Bruno de Vasconcelos Leitão
Antonio Bruno de Vasconcelos Leitão
CBCleverson Bringhenti
Cleverson Bringhenti
TTTakachi Tomita
Takachi Tomita
FSFRANCO J S SILVA
FRANCO J S SILVA
CXCarlos XIsto
Carlos XIsto
TGTomas Grönstedt
Tomas Grönstedt

12 August 2024 in Aerospace
Verified
Journal Article
Open access
PDF file
RDRuben Bruno Diaz
Ruben Bruno Diaz
TTTakachi Tomita
Takachi Tomita
CBCleverson Bringhenti
Cleverson Bringhenti
FSFRANCO J S SILVA
FRANCO J S SILVA
DCDiogo Ferraz Cavalca
Diogo Ferraz Cavalca
The internal losses in the tip clearance region strongly influence the compressor performance and its operational range. Previous research proved that passive wall treatments with circumferential grooves in axial compressors effectively increase the compressor stall margin. The vortex generated inside the circumferential grooves creates a resistance to the flow that leaks into the tip clearance region of the compressor. However, most works found in the literature on circumferential grooves in axial compressors deal only with high-performance single-stage axial compressors. Therefore, there is a need to investigate and analyze the behavior of circumferential grooves in a multi-stage environment. In the present work, a passive wall treatment with circumferential grooves was implemented in a multi-stage axial compressor. Different configurations of circumferential grooves were created at the casing of the first and second rotor rows used in a four-stage axial flow compressor. Numerical simulations were performed to evaluate the influence of the circumferential grooves on the performance of a multi-stage axial compressor. The results obtained after the simulations for the different circumferential groove configurations were compared with the results obtained for the compressor without casing treatment (smooth wall) for different rotational speeds. Furthermore, the complete compressor map characteristics were simulated for the different casing treatment configurations, and the results were compared with the compressor characteristics of the smooth wall case. The passive wall treatment with circumferential grooves produced changes in the multi-stage axial compressor flow field, especially in the tip clearance region, improving the compressor stability mainly for part load speeds.

1 January 2011
Verified
Conference Paper
Closed access
PDF file
JBJoa˜o Roberto Barbosa
Joa˜o Roberto Barbosa
FSFRANCO J S SILVA
FRANCO J S SILVA
TTTakachi Tomita
Takachi Tomita
CBCleverson Bringhenti
Cleverson Bringhenti
During the design of a gas turbine it is required the analysis of all possible operating points in the gas turbine operational envelope, for the sake of verification of whether or not the established performance might be achieved. In order to achieve the design requirements and to improve the engine off-design operation, a number of specific analyses must be carried out. This paper deals with the characterization of a small gas turbine under development with assistance from ITA (Technological Institute of Aeronautics), concerning the compressor variable geometry and its transient operation during accelerations and decelerations. The gas turbine is being prepared for the transient tests with the gas generator, whose results will be used for the final specification of the turboshaft power section. The gas turbine design has been carried out using indigenous software, developed specially to fulfill the requirements of the design of engines, as well as the support for validation of research work. The engine under construction is a small gas turbine in the range of 5 kN thrust / 1.2 MW shaft power, aiming at distributed power generation using combined cycle. The work reported in this paper deals with the variable inlet guide vane (VIGV) transients and the engine transients. A five stage 5:1 pressure ratio axial-flow compressor, delivering 8.1 kg/s air mass flow at design-point, is the basis for the study. The compressor was designed using computer programs developed at ITA for the preliminary design (meanline), for the axisymmetric analysis to calculate the full blade geometry (streamline curvature) and for the final compressor geometry definition (3-D RANS and turbulence models). The programs have been used interatively. After the final channel and blade geometry definition, the compressor map was generated and fed to the gas turbine performance simulation program. The transient study was carried out for a number of blade settings, using different VIGV geometry scheduling, giving indication that simulations needed to study the control strategy can be easily achieved. The results could not be validated yet, but are in agreement with the expected engine response when such configuration is used.

1 January 2022 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
JOJosé Charles Moraes de Oliveira
José Charles Moraes de Oliveira
FSFRANCO J S SILVA
FRANCO J S SILVA
LMLuiz Fernando Nazaré Marques
Luiz Fernando Nazaré Marques
ARAdriano Alves Rabelo
Adriano Alves Rabelo
RESUMO Os refratários de alumina estão constantemente sujeitos a variações bruscas de temperatura e elevados esforços mecânicos. Nesse contexto, busca-se por soluções que evitem ou diminuam a degradação dos refratários provenientes dos processos industriais. Os materiais refratários do sistema alumina-mulita-zircônia apresentam excelente resistência ao choque térmico e possibilitam alto desempenho em solicitações de desgaste e corrosão. Neste trabalho, avaliamos refratários de alta-alumina com 5,0 %m. de zircônia nanométrica, verificando a influência da granulometria dos agregados de mulita, mantida em 20 %m. Utilizou-se separadamente agregados de mulita de até 1 mm e de finos da ordem de 75 mm, substituindo parcialmente a alumina, e os corpos de prova foram sinterizados a 1600 °C por 5 horas. Utilizamos as técnicas de microscopia eletrônica de varredura e a difração de raios X para identificação e das fases presentes. A energia de fratura foi avaliada utilizando ensaio de flexão em três pontos, enquanto a resistência ao dano por choque térmico, utilizando-se gradientes térmicos de 800 °C para amostras submetidas até quinze ciclos térmicos combinados com ensaios de flexão. A composição contendo agregado de mulita fina e de zircônia aglomerada proporciona energia de fratura superior ao refratário, no entanto, o agregado com granulometria grossa tende a oferecer boa resistência ao dano por choque térmico devido a presença de porosidade lateral aos agregados.

1 April 2021 in Cadernos de Prospecção
Verified
Journal Article
Open access
PDF file
MAManoel Enio Almeida Aguiar
Manoel Enio Almeida Aguiar
SSSidnei Cerqueira dos Santos
Sidnei Cerqueira dos Santos
FSFRANCO J S SILVA
FRANCO J S SILVA
AMAndrea Hentz de Mello
Andrea Hentz de Mello
A Propriedade Intelectual, no Brasil, é regulamentada pela Lei n. 9.279, de 14 de maio de 1996, conhecida como Lei da Propriedade Industrial (LPI). A mencionada lei regula direitos e obrigações relativos à Propriedade Industrial. É nesse ordenamento que existe a previsão da figura jurídica da Indicação Geográfica (IG). O Estado do Pará é uma unidade federativa extremamente rica em biodiversidades, produtos e serviços que poderiam ter sua origem protegidas pela IG, porém, possui, efetivamente, apenas um registro concedido. O objetivo deste trabalho é demonstrar o paradoxo existente entre a propriedade intelectual e as potencialidades existentes no Estado do Pará. Foram realizados estudos bibliográficos e exploratórios, cujos resultados demonstram que há muitas possibilidades no campo da IG. Conclui-se que esse paradoxo pode ser enfrentado a partir do avanço das articulações de diversos atores na busca pela institucionalização do direito de propriedade intelectual das riquezas distintivas paraenses.