The vibration process applied to fresh concrete is an important link in the construction process, but the lack of effective monitoring and evaluation methods results in the quality of the vibration process being difficult to control and, therefore, the structural quality of the resulting concrete structures difficult to guarantee. In this paper, according to the sensitivity of internal vibrators to vibration acceleration changes under different vibration media, the vibration signals of vibrators in air, concrete mixtures, and reinforced concrete mixtures were collected experimentally. Based on a deep learning algorithm for load recognition of rotating machinery, a multi-scale convolution neural network combined with a self-attention feature fusion mechanism (SE-MCNN) was proposed for medium attribute recognition of concrete vibrators. The model can accurately classify and identify vibrator vibration signals under different working conditions with a recognition accuracy of up to 97%. According to the classification results of the model, the continuous working times of vibrators in different media can be further statistically divided, which provides a new method for accurate quantitative evaluation of the quality of the concrete vibration process.
In this paper, the effect of a newly developed superfine basalt powder (SB) on the fresh and mechanical properties of cement paste was studied. The concept of water film thickness (WFT) was cited to explain the influence of SB on fresh and mechanical properties and related mathematical model formulas were established. In addition, the relationship between the fresh properties and mechanical properties of paste was also explored. The results indicated that SB can improve the segregation resistance and cohesiveness. The maximum improvement rate relative to the control cement paste was 75.4% and 50.4%, respectively. The 5% SB and 10% SB reduced the fluidity in the range of 4.1–68.7% but increased the early and late compressive strength in the range of 1.2–25.7% compared to control cement paste under different water/cementitious materials (W/CM) ratios. However, the influence of 20% SB on fluidity and compressive strength was opposite to the above behavior, and the increase rate and decrease rate were 1.8–11.8% and 1.1–13.9% respectively. The WFT was the most important factor that determined the compressive strength, rheological parameters, and flow parameters of paste containing SB, while the substitute content of SB and WFT together determined the bleeding rate and cohesiveness. Among them, the correlation between bleeding rate and WFT increased with time. The empirical mathematical models between WFT, fresh properties, and compressive strength were established and verified by other mineral admixtures, which were successfully extended and applied to the entire field of cement-based materials
To reduce land use and avoid further pollution, incineration for power generation has become the main method for municipal solid waste treatment. This research focused on the potential for transforming Municipal Solid Waste Incineration Bottom Ash (MSWIBA) into a finely ground powder. The impact of the powder’s fineness and the amount of water used on its effectiveness was analyzed using a method called grey theory. MSWIBA was used as a partial substitute for cement in making MSWIBA foam concrete and lightweight wall panels. By modifying the fineness and water utilization of the recycled micro-powder, its maximum activity index can be increased to 90.1. This study determined the influence of factors including apparent dry density, water–cement ratio, foaming agent dilution ratio, and admixture dosage on the strength of the recycled foam concrete, and established the optimal mix ratio. This study employed a combination of physical experiments and numerical simulations to elucidate the impact of panel material, core layer thickness, and layer sequence on sound insulation performance. The simulation results were in close agreement with the experimental findings.
Aiming at the problems of incomplete particle sieving and excessive residual fine particles in the traditional vibrating screen during the grading process of rockfill materials, this study proposes a secondary screening enhancement method by adding an auxiliary screen to the screen box to further improve the screening efficiency. Through the EDEM simulation software, a vibrating screening model with a four-layer screen structure was established, and an improved optimization scheme of adding an auxiliary screen in the screen box was designed. Systematic simulation analysis was conducted on the generated particles. The research content includes the influence of different screen angles, numbers of layers, amplitudes, frequencies, and direction angles on the screening efficiency, as well as the optimization and analysis of the secondary screening process with the auxiliary screen in the screen box. The simulation results show that the secondary screening scheme with the auxiliary screen in the screen box can significantly improve the screening efficiency of particles of various sizes. Based on rigorous verification simulations, the total efficiency increased from 92.4% in the traditional single-pass screening to 96.5%. While ensuring conservative estimates, this result still demonstrates a significant efficiency advantage over conventional designs.