Changes to the surface morphology of a cylinder immersed in a uniform flow may affect the surrounding flow characteristics. Circular cylinders with various symmetric strips attached are ideal models for studying this subject. This study investigates the flow-induced vibration (FIV) of a three-dimensional cylinder with symmetric strips attached using the delayed detached-eddy simulation method. First, the effects of the 22 different types of strip parameters are evaluated on the fixed cylinder. Then, P5-60-20 (location , coverage , and thickness ) is chosen to explore the transverse FIV. P5-60-20 vibration responses exhibit four distinct branches—initial branch, passive upper branch, transition branch from vortex-induced vibration (VIV) to galloping, and pure galloping—which correspond to the classic initial, upper, lower, and desynchronization regions of the circular cylinder. Through a detailed discussion of each branch, it is discovered that the passive upper branch is significantly different from the upper branch, despite their similar vibration amplitudes and frequencies. The upper branch is induced by the flutter in the presence of intense three-dimensional flow. However, the passive upper branch is caused by symmetric strips, which promote spanwise correlation, prevent lift phase shifting, and dampen the effect of three-dimensional flow. Consequently, at higher reduced velocities, the transition from VIV to galloping and pure galloping is triggered.
Minor changes to the surface of a cylinder can significantly influence the associated flow characteristics. This paper describes a three-dimensional numerical investigation of a cylinder attached with symmetric strips in a uniform flow at . The location ( ), thickness ( ), and coverage ( ) of the strips are selected for study. Two flow modes, patterns A and D, can be characterized in the flow around this passive turbulence control cylinder by their vortex enhancement and suppression effects. The Strouhal number of pattern A is very close to the response of a smooth cylinder. For cylinders with the upper strip located at from the front stagnation point, the lift force correlation in the spanwise direction is enhanced by the forced flow separation. When the front edge of the upper strip is fixed at , the thickness of the strips plays a vital role: the drag and lift force increase linearly as the thickness increases, whereas the Strouhal number and the vortex shedding frequency decrease.
Niobium (Nb) and zirconium dioxide (ZrO2) were doped into hydroxyapatite (HA) to fabricate HA-based composite coatings prepared on a ZK60 magnesium alloy by plasma spraying technology to improve anti-corrosion and biocompatibility for clinical applications. The results revealed that the Nb-enriched coating exhibits fewer cracks and pores with a flat surface due to the decreased temperature gradient during spraying, and small needle-like structures can fill the cracks and pores in the ZrO2-contained coating, resulting in a more uniform and dense surface. Compared to coatings with only niobium or zirconium dioxide, the ZrO2/Nb/HA composite coating significantly enhanced the mechanical properties and corrosion resistance of the magnesium alloys. Among all the specimens, the ZrO2/HA coating and ZrO2/Nb/HA coating revealed high surface hardness values (327.73 HV and 293.80 HV, respectively). However, the higher hardness value made the ZrO2/HA coating fragile and more likely to crack, while the ZrO2/Nb/HA coating avoided this shortcoming and exhibited a more comprehensive performance. During immersion tests, the ZrO2/Nb/HA coating exhibited a gradual pH increase and minimal mass loss, and the cytocompatibility test demonstrated promising cellular activity.
This study conducted a systematic investigation on how Ca content affected Mg-6Al-1Sn alloys as anodes for Mg-air batteries in terms of their microstructure, electrochemical corrosion behavior, and discharge performance. According to the investigation results, incorporating Ca induces the formation of blocky β-Mg17Al12 phases containing Ca and refines the grain structure. Compared to Mg alloys without Ca, the alloys with Ca exhibit significantly improved self-corrosion resistance because the preferential enrichment of Ca at the grain boundaries within β-Mg17Al12 phases reduces the potential difference between β-Mg17Al12 phases and Mg matrix. Consequently, galvanic corrosion is mitigated, together with the effective suppression of the self-corrosion reaction of Mg anodes. Additionally, Mg alloy shows a higher anode utilization efficiency with Ca content. The combined results indicate that Mg-6Al-1Sn-0.5Ca alloy exhibits superior self-corrosion resistance and discharge properties vs. other tested compositions. Furthermore, the Mg-air battery using Mg-6Al-1Sn-0.5Ca alloy as the anode demonstrates a heavier average discharge potential and a utilization efficiency of 71.12%, which is 7.56% higher than Mg-6Al-1Sn alloy.
In the field of fluid dynamics, the Reynolds number is a key parameter that influences the flow characteristics around bluff bodies. While its impact on flow around stationary cylinders has been extensively studied, systematic research into flow-induced vibrations (FIVs) under these conditions remains limited. This study utilizes numerical simulations to explore the FIV characteristics of smooth cylinders and passive turbulence control (PTC) cylinders supported elastically within a Reynolds number range from 0.8 × 104 to 1.1 × 105. By comparing the vibration responses, lift coefficients, and wake structures of these cylinders across various Reynolds numbers, this paper aims to elucidate how Reynolds numbers affect the flow and vibration characteristics of these structures. The research employs images of instantaneous lift changes and vortex shedding across multiple sections to visually demonstrate the dynamic changes in flow states. The findings are expected to provide theoretical support for optimizing structural design and vibration control strategies in high-Reynolds-number environments, emphasizing the importance of considering Reynolds numbers in structural safety and design optimization.