Lu Yu

Ms. Lu Yu


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2024 in Coatings
Verified
Journal Article
Open access
PDF file
XWXiaofeng Wan
Xiaofeng Wan
SFSiyi Fang
Siyi Fang
XXXu Xu
Xu Xu
LYLu Yu
Lu Yu
JZJingling Zhou
Jingling Zhou
CMChunhui Ma
Chunhui Ma
Niobium (Nb) and zirconium dioxide (ZrO2) were doped into hydroxyapatite (HA) to fabricate HA-based composite coatings prepared on a ZK60 magnesium alloy by plasma spraying technology to improve anti-corrosion and biocompatibility for clinical applications. The results revealed that the Nb-enriched coating exhibits fewer cracks and pores with a flat surface due to the decreased temperature gradient during spraying, and small needle-like structures can fill the cracks and pores in the ZrO2-contained coating, resulting in a more uniform and dense surface. Compared to coatings with only niobium or zirconium dioxide, the ZrO2/Nb/HA composite coating significantly enhanced the mechanical properties and corrosion resistance of the magnesium alloys. Among all the specimens, the ZrO2/HA coating and ZrO2/Nb/HA coating revealed high surface hardness values (327.73 HV and 293.80 HV, respectively). However, the higher hardness value made the ZrO2/HA coating fragile and more likely to crack, while the ZrO2/Nb/HA coating avoided this shortcoming and exhibited a more comprehensive performance. During immersion tests, the ZrO2/Nb/HA coating exhibited a gradual pH increase and minimal mass loss, and the cytocompatibility test demonstrated promising cellular activity.

16 April 2025 in Metals
Verified
Journal Article
Open access
PDF file
NNNing Nie
Ning Nie
LYLu Yu
Lu Yu
XXXu Xu
Xu Xu
田奇田 奇缘
田 奇缘
CDChenchen Ding
Chenchen Ding
Hui WangHui Wang
Hui Wang
In this study, machine hammer peening (MHP) was employed to enhance the surface properties of CuSn12 alloys, and the effects of different impact energies on the surface morphology, mechanical properties, and electrochemical properties were systematically investigated. The results revealed that the surface morphology evolution after MHP treatment exhibited unique non-monotonic characteristics, which significantly differed from the surface effects of conventional shot peening technology. Microhardness tests indicated that the surface hardness increased by 40% to approximately 150 HV after treatment with 3.5 J impact energy. Friction and wear tests demonstrated that specimens treated with 2.7 J impact energy exhibited optimal wear resistance, with an 82.7% reduction in volume wear loss, and the wear mechanism transformed from composite wear to mild fatigue wear. Electrochemical performance tests showed that corrosion resistance continuously improved as the impact energy increased from 2.7 J to 3.5 J, primarily attributed to grain refinement and passive film formation; however, treatment with 1.7 J impact energy resulted in decreased corrosion resistance. The results demonstrate that optimizing MHP process parameters can significantly enhance the overall properties of CuSn12 alloys, providing a novel technical approach for the surface-strengthening of this alloy.

22 November 2024 in Coatings
Verified
Journal Article
Open access
PDF file
YU LIUYU LIU
YU LIU
YWYefu Wang
Yefu Wang
LYLu Yu
Lu Yu
YYYing Yang
Ying Yang
NNNing Nie
Ning Nie
YSYifu Shen
Yifu Shen
In industrial production, 7075 aluminum alloy (A7075) is prized for its strength and light weight. However, heat treatment can reduce its hardness and wear resistance. Therefore, proper surface treatments are often necessary to optimize its mechanical properties. In this work, a hammering tool attached to a robotic arm was employed to impact the surface of A7075 using different impact energies, and the surface hardness, morphology, roughness, and frictional characteristics of samples subjected to machine hammer peening (MHP) treatment were analyzed to explore the strengthening mechanism of MHP. The results indicate that the hardness increased to a maximum value of 235 HV with rising impact energy, whereas the depth of influence (2 mm) was almost unaffected by the impact energy. Microstructural analysis revealed significant grain refinement, especially at 2.7 J. The surface roughness increased significantly to about 7.2 μm, then dropped to around 3.7 μm when the impact energy increased to 2.7 J. Finally, the roughness decreased to ~6.8 μm. In addition, the samples that were strengthened by MHP demonstrated low friction coefficients (about 0.27) and wear volume (minimum value of 7.67/10−4 mm3), implying that MHP can effectively improve the wear resistance of A7075. Observation by SEM revealed that the corresponding wear mechanism is mainly attributable to mild oxidative wear and three-body wear.

29 June 2026 in Metals
Verified
Journal Article
Open access
PDF file
RWRui Wang
Rui Wang
JHJUAN HOU
JUAN HOU
LYLu Yu
Lu Yu
XXXu Xu
Xu Xu
Lihong SuLihong Su
Lihong Su
XHXi Huang
Xi Huang
CoCrFeMnNi high-entropy alloy (HEA) coatings were fabricated on an S41500 stainless steel substrate by laser cladding and subsequently strengthened using machine hammer peening (MHP) at three hammering energies of 1.7 J, 3.5 J, and 5.0 J. The effects of MHP treatment on the phase structure, surface morphology, microhardness, and tribological properties of the coatings were systematically investigated. The results showed that all coatings retained a single-phase face-centered cubic (FCC) structure after MHP treatment, indicating excellent microstructural stability during impact-induced strengthening. With increasing hammering energy, the surface morphology gradually evolved from discrete hammering indentations to a more continuous orange-peel-like texture, while the surface roughness initially increased and then decreased. MHP significantly enhanced the surface hardness of the coatings. In particular, the MHP3.5 sample exhibited the highest surface hardness of approximately 420 HV, representing an increase of about 120% compared with the untreated coating. Under dry sliding conditions at a load of 30 N, the MHP3.5 sample exhibited the lowest and most stable friction coefficient, maintaining a steady-state value of approximately 0.40–0.45. Its specific wear rate decreased by nearly 45% compared with that of the untreated coating. The improved wear resistance was mainly attributed to the combined effects of strain hardening, grain refinement, and dislocation strengthening induced by machine hammer peening. Considering the hardness, friction coefficient, and specific wear rate results together, a hammering energy of 3.5 J was identified as the most suitable MHP parameter under the low-load wear conditions investigated in this study.