A hypervapotron (HV) loop test facility was built to conduct some experiments of heat transfer. Phenomena of HV were observed using the techniques of planar laser-induced fluorescence, high-speed photography, and particle image velocimetry. According to the design of the ITER cooling water system, the fluid flow and condition parameters were utilized: 1) CuCrZr alloy material; 2) triangular and rectangular fin structures; 3) inlet subcooling temperature of 298 K; and 4) rhodamine B solution flow velocity of 0.3-0.5 m/s. It was found that the heat transfer coefficient of the rectangular fin was 1.3-1.5 times higher than that of the triangular fin under the same test conditions. Furthermore, the preliminary mechanism of the heat transfer was explained by the coupling effect of the vortex flow with vapor bubble in the fin pitch, and the heat transfer efficiency was extraordinarily dependent on maintaining the time of vortex formation between the fins.
24 April 2018 in IEEE Transactions on Plasma Science
The heat fluxes on the lower outer divertor plate were calculated using the DFLUX code with the surface temperature measured by the IR camera on the experimental advanced superconducting tokamak. The analyzed discharges were lower single-null divertor configuration discharges with different auxiliary heating: lower hybrid wave current drive (LHCD) combined with neutral beam injection (NBI) and LHCD combined with ion cyclotron resonant heating (ICRH). The surface temperature of the lower outer divertor target plate was about 170 °C in the LHCD + NBI H-mode, with the high temperature mostly distributed in the location near the joint of the dome and the outer target plate. The temperature increased as the NBI was turned on and fluctuated due to edge localized modes (ELMs). The heat flux reached nearly 4 MW/m 2 when ELMs appeared and declined to less than 1 MW/m 2 when the NBI was turned off. Temperature distribution with extreme toroidal asymmetry was observed in the selected LHCD + ICRH H-mode discharge. The surface temperature on the lower outer divertor target plate was up to 220 °C in one region with broader temperature distribution. During the LHCD + ICRH H-mode, the peak heat flux was not seen during the period of ICRH injection, though a brief spike in heat flux was observed at the beginning of the ICRH injection. The full-width at half-maximum of the heat flux profile as a function of divertor target plate location of the LHCD + ICRH H-mode is three times that of the LHCD + NBI H-mode.
11 May 2018 in IEEE Transactions on Plasma Science
A simulation of J-TEXT ohmic disruptive discharge has been achieved by using of the Tokamak Simulation Code (TSC) model. TSC is a numerical model of an axisymmetric free-boundary tokamak plasma and the associated control systems. The anomalous transport coefficient of disruption was adjusted according to heat transport across large magnetic island to mimic a sudden disruption. The simulation result of plasma current, electron temperature, loop voltage, and the disruption is compared with J-TEXT experimental disruptive discharge data. According to the simulation result, the dynamic response of one test plasma-facing module was calculated; the numerical results show that the maximum stress of the test module is in safety range.
Real-time prediction of the growth rate of internal kink modes and the timely implementation of control measures are crucial for the stable operation of tokamak devices. In this study, machine learning techniques are combined with the three-dimensional toroidal nonlinear magnetohydrodynamic code CLT (Ci-Liu-Ti) to enable real-time prediction of the growth rate of internal kink modes. The CLT code is first utilized to generate a dataset of internal kink mode growth rates with 15 input features. Based on this dataset, four machine learning algorithms are applied to predict the growth rate of internal kink modes within a timescale of less than 25 microseconds. Experimental results indicate that Random Forest model achieves the highest coefficient of determination (R2) at 95.07%. Additionally, dataset size was progressively expanded, starting from 50 data points and increasing by 10 points at a time, resulting in a total of 16 datasets of varying sizes. Random Forest and other machine learning models are trained on each of these 16 datasets. The results suggest that the current dataset contains a sufficient volume of data, and the four machine learning models trained exhibit adequate generalization capabilities, making the predictions of the internal kink mode growth rate reliable.
Joint TEXT (J-TEXT) is an iron-core tokamak. The iron core can reduce the requirement of heating power supplies, and it also has a significant effect on the poloidal magnetic field during J-TEXT discharge. However, it is difficult to simulate an iron-core tokamak discharge process for many tokamak simulation codes (TSCs), such as TSC and DINA. Thus, the influence of the iron core on the J-TEXT magnetic field is analyzed by the theoretical model and the ANSYS model and compared with experimental results. ANSYS simulation shows that the influence of the iron core on the toroidal magnetic field can be ignored, but it has a significant impact on the poloidal magnetic field. By the comparison of ANSYS simulation and experimental results, the correction coefficient of the poloidal field with and without iron core is obtained, which can be used in some non iron-core TSC.
A one-dimensional model, in which the ionization and collision are omitted in the Debye sheath region, is applied to investigate the effect of the superthermal electrons on the heat flux through a magnetized sheath. For different temperatures and concentrations of the superthermal electron, and magnitudes and directions of the magnetic field, the profiles of plasma parameters including ion density and flow velocity perpendicular to the wall, the background and superthermal electron densities, and sheath potential in the presheath region are calculated. The variation of the plasma density and sheath potential drop at the Debye sheath entrance with the superthermal electrons and magnetic field modifies the particle and heat fluxes across the Debye sheath to the material surface. The sheath heat transmission coefficient can increase significantly even for a very small superthermal electron population. The dependence of the sheath heat transmission coefficient on the magnetic field angle decreases with the contribution of the superthermal electron in a strong magnetized sheath. When investigation of the heat flux including the superthermal electrons to a water-cooled W/Cu monoblack for the tokamak divertor, compared to the case of without superthermal electrons, it is found that the increase in both heat flux to the material surface and surface temperature of the material is mainly due to the enhancement of the sheath potential drop caused by the superthermal electrons, but the increase in the latter is not as pronounced as the former.