Hubert Fuks

Dr. Hubert Fuks


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2021 in Catalysts
Verified
Journal Article
Open access
PDF file
PRPiotr Rychtowski
Piotr Rychtowski
Beata TrybaBeata Tryba
Beata Tryba
HFHubert Fuks
Hubert Fuks
Maria Angeles Lillo-RodenasMaria Angeles Lillo-Rodenas
Maria Angeles Lillo-Rodenas
MRM.Carmen Román-Martínez
M.Carmen Román-Martínez
TiO2 was placed in heat-treatment at the temperature of 400–500 °C under flow of hydrogen gas in order to introduce some titania surface defects. It was observed that hole centers in TiO2 were created during its heat treatment up to 450 °C, whereas at 500 °C some Ti3+ electron surface defects appeared. The type of titania surface defects had a great impact on the mechanism of acetaldehyde decomposition under irradiation of artificial visible light. Formation of O•− defects improved both acetaldehyde decomposition and mineralization due to the increased oxidation of adsorbed acetaldehyde molecules by holes. Contrary to that, the presence of electron traps and oxygen vacancies in titania (Ti3+ centers) was detrimental for its photocatalytic properties towards acetaldehyde decomposition. It was proved that transformation of acetaldehyde on the TiO2 with Ti3+ defects proceeded through formation of butene complexes, similar as on rutile-type TiO2. Formed acetic acid, upon further oxidation of butene complexes, was strongly bound with the titania surface and showed high stability under photocatalytic process. Therefore, titania sample heat-treated with H2 at 500 °C showed much lower photocatalytic activity than that prepared at 450 °C. This study indicated the great impact of titania surface defects (hole traps) in the oxidation of acetaldehyde and opposed one in the case of defects in the form of Ti3+ and oxygen vacancies. Oxidation abilities of TiO2 seem to be important in the photocatalytic decomposition of volatile organic compounds (VOCs) such as acetaldehyde.

Verified
Journal Article
Open access
PDF file
HFHubert Fuks
Hubert Fuks
PKPaweł Kochmański
Paweł Kochmański
Elżbieta TomaszewiczElżbieta Tomaszewicz
Elżbieta Tomaszewicz
New Gd3+- and Mn2+-co-doped calcium molybdato-tungstates with the chemical formula of Ca1−3x−yMny▯xGd2x(MoO4)1−3x(WO4)3x (labeled later as CaMnGdMoWO), where ▯ denotes vacant sites in the crystal lattice, 0 < x ≤ 0.2500 and y = 0.0200 as well as 0 < y ≤ 0.0667 and x = 0.1667 were successfully synthesized by high-temperature solid-state reaction method and combustion route. Obtained ceramic materials crystallize in scheelite-type structure with space group I41/a. Morphological features and grain sizes of powders under study were investigated by SEM technique. Spectroscopic studies within the UV-vis spectral range were carried out to estimate the direct band gap (Eg) and Urbach energy (EU) of obtained powders. EPR studies confirmed the existence of two types of magnetic objects, i.e., Mn2+ and Gd3+ ions, and significant antiferromagnetic (AFM) interactions among them.

8 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
Sławomir Maksymilian KaczmarekSławomir Maksymilian Kaczmarek
Sławomir Maksymilian Kaczmarek
JMJerzy Zbigniew Michalski
Jerzy Zbigniew Michalski
GLGrzegorz Leniec
Grzegorz Leniec
HFHubert Fuks
Hubert Fuks
TFTadeusz Frączek
Tadeusz Frączek
ADAgata Dudek
Agata Dudek
This paper presents the relationship between the chemical composition and size of steel balls, the parameters of the nitriding process, and their magnetic properties, defined in this study by ferromagnetic resonance (FMR) and SQUID. Balls made from AISI 1010 and AISI 52100 steels, with diameters of 2.5 and 3 mm, respectively, were investigated. On samples made of AISI 1010 and AISI 52100 steel, single-phase layers of iron nitrides γ’ with a thickness of gmp = 50 and 37 μm, respectively, were produced. Then, the samples were annealed at a temperature of 520 °C for 4 h in an inert atmosphere (N2/Ar) at a pressure of 200 Pa. After the nitriding processes, steel balls were subjected to standard physical metallurgy and X-ray examinations. During annealing of nitrided layers with a two-phase layer of iron nitrides, at first, the transformation of the ε phase into the γ’ phase with the release of nitrogen into the atmosphere takes place. The FMR signals did not originate from isolated ions, but from more magnetically complex systems, e.g., Fe–Fe pairs or iron clusters, while the observed FMR line position is normally even lower and occurs for a magnetic induction below 200 mT. The fact that the magnetic centers did not contain mainly isolated Fe ions, additionally confirmed the abnormal increase in resonance signal intensity as a function of temperature, which is a behavior inconsistent with the Curie–Weiss law. The results obtained from measurements by the SQUID method, recording variations in magnetization as a function of temperature, confirm the untypical reinforcement of the magnetic conditions of the samples with the increase in temperature. For the samples tested, the magnetization was relatively weaker when the tests were conducted in a stronger magnetic field.

4 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
Elżbieta TomaszewiczElżbieta Tomaszewicz
Elżbieta Tomaszewicz
GDGrażyna Dąbrowska
Grażyna Dąbrowska
HFHubert Fuks
Hubert Fuks
PKPaweł Kochmański
Paweł Kochmański
New Nd3+-doped cadmium molybdato-tungstates with the chemical formula of Cd1−3x▯xNd2x(MoO4)1−3x(WO4)3x (where x = 0.0283, 0.0455, 0.0839, 0.1430, 0.1875, 0.2000, 0.2500, and ▯ denotes a vacant site in the crystal lattice) were successfully synthesized by the high-temperature solid state reaction method, using CdMoO4 and Nd2(WO4)3 as the initial reactants. The structure and change in their lattice parameters as a function of Nd3+ ion concentration were investigated by the XRD (X-ray diffraction) method. The surface morphology and grain size of the doped materials were characterized by SEM (scanning electron microscopy). Their thermal properties and initial reactants were analyzed by DTA-TG (differential thermal analysis coupled with thermogravimetry) techniques. The optical properties of the Nd3+-doped cadmium molybdato-tungstates, such as optical band gap, were determined by UV–vis–NIR (ultraviolet–visible–near infrared) spectroscopy. The EPR (electron paramagnetic resonance) technique provided information on the type of magnetic interactions between Nd3+ ions.

1 June 2023 in Metals
Verified
Journal Article
Open access
PDF file
Sławomir Maksymilian KaczmarekSławomir Maksymilian Kaczmarek
Sławomir Maksymilian Kaczmarek
JMJerzy Zbigniew Michalski
Jerzy Zbigniew Michalski
TFTadeusz Frączek
Tadeusz Frączek
ADAgata Dudek
Agata Dudek
HFHubert Fuks
Hubert Fuks
GLGrzegorz Leniec
Grzegorz Leniec
This paper discusses the changes in the phase composition and magnetic properties of the AISI 1010 and AISI 1085 steels that were nitrided at 570 °C in an ammonia atmosphere for 5 h and that were then annealed at 520 °C in a N2/Ar atmosphere for 4 h. The test samples were made in the form of balls with diameters of less than 5 mm. The thickness of the obtained iron nitride layers was assessed through metallographic tests, while the phase composition was verified through X-ray tests. The magnetic properties were determined using ferromagnetic resonance (FMR) and superconducting quantum interference device (SQUID) techniques. Our research shows that, during the annealing of iron nitrides with a structure of ε + γ′, the ε phase decomposes first. As a result of this process, an increase in the content of the γ′ phase of the iron nitride is observed. When the ε phase is completely decomposed, the γ′ phase begins to decompose. The observed FMR signals did not come from isolated ions but from more magnetically complex systems, e.g., Fe–Fe pairs or iron clusters. Studies have shown that nitriding and annealing can be used to modify the magnetic properties of the tested steels.

2 November 2026 in Materials
Verified
Journal Article
Open access
PDF file
Elżbieta TomaszewiczElżbieta Tomaszewicz
Elżbieta Tomaszewicz
MKMagdalena Kotfica
Magdalena Kotfica
HFHubert Fuks
Hubert Fuks
PKPaweł Kochmański
Paweł Kochmański
New Er3+-doped lead tungstates and molybdate–tungstates with the chemical formulae Pb1−3x▯xEr2xWO4 (0 < x ≤ 0.0283) and Pb1-3x▯xEr2x(MoO4)1-3x(WO4)3x (0 < x ≤ 0.0536), where ▯ denotes a vacant crystallographic site, were successfully synthesized via a high-temperature solid-state reaction method using PbWO4 or PbMoO4 and Er2(WO4)3 as starting reactants. X-ray diffraction and scanning electron microscopy analyses confirmed the formation of single-phase, tetragonal scheelite-type materials (space group I41/a) with an average crystallite size ranging from approximately 50 to 100 μm. The Er3+-doped ceramic materials remained stable up to their melting points and did not undergo any polymorphic transformation. Their melting points were lower than those of the corresponding scheelite-type matrix, namely, PbWO4 and PbMoO4. UV–Vis–NIR diffuse reflectance measurements demonstrated that all Er3+-doped materials are insulating and exhibit indirect optical transitions. The incorporation of Er3+ leads to a reduction in the optical band gap energy, from 3.73 to 3.47 eV for the doped tungstates and from 3.17 to 3.01 eV for the doped molybdate–tungstates, accompanied by a simultaneous increase in the Urbach energy. The refractive indices estimated using seven different empirical models exhibit only a weak dependence on Er3+ concentration and remain relatively high (approximately 2.15–2.50) for both material series.