Introduction: The demand to increase reliability and reduce maintenance costs drives the search for new condition monitoring solutions of machines. Bearings are of special interest in this matter as they are main contributors to machine downtime. Therefore, this article investigates the electric behavior of a hydrodynamic journal bearing using impedance measurement.Methods: For that purpose measurements are taken in boundary lubrication, mixed lubrication and hydrodynamic lubrication of a hydrodynamic journal bearing. In order to interpret the behaviour observed in these measurements, a phenomenological model is developed using the quantitative working space model. The measurement results are also interpreted using analogies to the Stribeck curve as a known tribological model. Additionally, measurements in mixed lubrication are analysed in detail.Results: These measurements show that the electric behaviour of journal bearings changes significantly within the mixed lubrication regime. This change in behaviour shows three distinct states within mixed lubrication which helps to identify destructive operating conditions. Furthermore, the measurements potentially allow the detection of deformation or damage of the bearing in mixed lubrication.Discussion: The quantitative analysis of the electric behaviour of journal bearings is possible in the mixed lubrication regime and can be used in future to extract condition and operating information from a system during operation.
This contribution explores the development of a digital twin for industrial valves, with a focus on mitigating the costly consequences of valve malfunctions in large-scale industrial environments. Industrial valves are critical components in fluid and gas control systems where unexpected failures can lead to significant downtime and financial loss. Digital twins as virtual replicas of physical systems offer a promising solution as they enable real-time monitoring and predictive maintenance. This paper looks at the creation of a digital twin for a specific valve type (74BS from SchuF Armaturen und Apparatebau GmbH) and considers key aspects such as model development, sensor integration and IT infrastructure. A test bench is constructed to collect the measured values to support the validation of the digital twin. The integration of sensors and the development of an IT system for data processing are also described in detail. Finally, the technically relevant frequencies are identified in an FFT.
The condition monitoring of machine elements and, more precisely, journal bearings, is beneficial to prevent unnecessary wear and identify critical operating conditions. One method for that is the monitoring of the electric behavior of the bearing by monitoring its capacitance. While the general electric behavior of journal bearings is known, assessments of suitable measurement setups and data analysis methods are usually neglected. This contribution identifies potential measurement setups and analysis methods used in the literature for monitoring rolling-element bearings or journal bearings. These setups and analysis methods are then discussed theoretically and based on measurements of the electric behavior of journal bearings. The findings show that voltage divider setups with AC signals are the most promising solution to monitor the journal bearing electrically. Linear regression algorithms can be used to obtain the amplitude and phase of the measured voltage signal. These values are then used to calculate the impedance and capacitance of the bearing. Lastly, this contribution investigates how existing PCT (percent contact time) analyses need to be altered to improve the precision and robustness of the analysis and allow for the physical interpretation of the measurement results. These findings may be used in the future to predict wear and identify critical operating conditions in journal bearings, such as mixed lubrication.
Electrically induced bearing failure is a reoccurring problem in modern drive train designs. To predict this damage, electrical models of bearings are required. In these models, the permittivity of lubricants is often assumed to be constant. However, the permittivity is dependent on pressure and temperature. For operating temperatures and pressures of journal bearings, no investigation of the permittivity of the lubricant exists. For this purpose, this study investigates the pressure and temperature dependence of lubricant permittivity using specially fabricated model bodies with layered structures of steel, ceramic insulating layers and copper in a parallel plate capacitor setup. Tests were performed applying temperatures between 20 °C and 100 °C and pressures between 1 and 250 bar. A mineral oil and a polyalkylene glycol (PAG) oil were examined. Results show a clear dependence of the permittivity on pressure and temperature. The mineral oil exhibits stronger pressure sensitivity, while the PAG oil shows more pronounced temperature dependence. Empirical equations to describe the permittivity as a function of temperature and pressure are derived. These findings provide relevant input for the selection of lubricants used in electrical environments. They also support the development of predictive models for modern electrical and tribological systems.
In this contribution the electrical behavior of helical gear contacts is investigated. The investigation is based on impedance measurements obtained on an industrial gearbox test bench. The results are analyzed to identify the qualitative influence of rotation speed, load, rotation direction, load direction and surface alterations. Furthermore, potentials and limitations of utilizing the electrical behavior of helical gear contacts for condition monitoring applications are discussed. The investigations show that the lubrication condition can be qualitatively identified based on the characteristics of the electrical behavior of the gear contact. Important influencing factors for the lubrication film thickness and consequently the impedance of the gear contact can be determined to be rotation speed and load but also rotation and load direction. Surface alterations like damages but also tooth pitch deviations in the region of single digit micrometers can be seen to have a measurable influence on the impedance signal of the gear contact. These effects can potentially be used for condition monitoring approaches. However, the ambiguity of the impedance signal due to the high number of influencing factors remains a limitation of this new measurement method. Another factor for the ambiguity of the impedance signal is the simultaneous contact of multiple teeth which are not distinguishable in the impedance signal. This contribution shows the potentials and limitations for the sensory utilization of the electrical behavior of helical gear contacts and highlights novel research gaps.
Several classes of machine elements are known to exhibit sensorial effects mainly in highly loaded tribological contacts such as helical gears, rolling elements and plain bearings. Departing from measurements in different lubrication conditions the question is discussed whether the underlying electrical effect can give rise to the hypothesis that machine elements have a fingerprint as a characteristic signal pattern. This signal pattern offers interesting features that may be exploited in future technical applications summarized as operational state monitoring including approaches like operational control, condition monitoring or predictive maintenance. Current opportunities and existing limits as well as a mutual uniqueness of the fingerprints are discussed based on the experimental evidence available so far.