Anodic TiO2 nanotube arrays decorated with Ni, Cu, and NiCu alloy thin films were investigated for the first time for the photocatalytic degradation of paracetamol in water solution under UV irradiation. Metallic co-catalysts were deposited on TiO2 nanotubes using magnetron sputtering. The influence of the metal layer composition and thickness on the photocatalytic activity was systematically studied. Photocatalytic experiments showed that only Cu-rich co-catalysts provide enhanced paracetamol degradation rates, whereas Ni-modified photocatalysts exhibit no improvement compared with unmodified TiO2. The best-performing material was obtained by sputtering a 20 nm thick film of 1:1 atomic ratio NiCu alloy: this material exhibits a reaction rate more than doubled compared with pristine TiO2, enabling the complete degradation of 10 mg L−1 of paracetamol in 8 h. The superior performance of NiCu-modified systems over pure Cu-based ones is ascribed to a Ni and Cu synergistic effect. Kinetic tests using selective holes and radical scavengers unveiled, unlike prior findings in the literature, that paracetamol undergoes direct oxidation at the photocatalyst surface via valence band holes. Finally, Chemical Oxygen Demand (COD) tests and High-Resolution Mass Spectrometry (HR-MS) analysis were conducted to assess the degree of mineralization and identify intermediates. In contrast with the existing literature, we demonstrated that the mechanistic pathway involves direct oxidation by valence band holes.
Antimony (Sb) contamination poses significant environmental and health concerns due to its toxic nature and widespread presence, largely from anthropogenic activities. This study addresses the urgent need for an accurate speciation analysis of Sb, particularly in water sources, emphasizing its migration from polyethylene terephthalate (PET) plastic materials. Current methodologies primarily focus on total Sb content, leaving a critical knowledge gap for its speciation. Here, we present a novel analytical approach utilizing frontal chromatography coupled with inductively coupled plasma mass spectrometry (FC-ICP-MS) for the rapid speciation analysis of Sb(III) and Sb(V) in water. Systematic optimization of the FC-ICP-MS method was achieved through multivariate data analysis, resulting in a remarkably short analysis time of 150 s with a limit of detection below 1 ng kg−1. The optimized method was then applied to characterize PET leaching, revealing a marked effect of the plastic aging and manufacturing process not only on the total amount of Sb released but also on the nature of leached Sb species. This evidence demonstrates the effectiveness of the FC-ICP-MS approach in addressing such an environmental concern, benchmarking a new standard for Sb speciation analysis in consideration of its simplicity, cost effectiveness, greenness, and broad applicability in environmental and health monitoring.
This study introduces a novel approach using an electrospray source coupled to an Orbitrap MS instrument to determine metal isotope ratios. The procedure involves forming a complex between the ion of interest and an appropriate ligand, generating gas-phase ions via electrospray ionization, selecting the complex mass by quadrupole filtering, and performing collisional fragmentation to yield free metal ions. The isotopic pattern of the free ion is then analyzed by high-resolution MS. The approach ensures high selectivity and interference-free spectra. A proof-of-concept study was conducted to determine Pb isotope ratios, focusing on identifying the factors that influence the accuracy and precision of the procedure. At this early stage, optimal accuracy was achieved even in the presence of matrix components by applying mass bias correction methods originally developed for other isotope ratio techniques; precision is comparable to that achieved by single-collector ICP-MS instrumentation. This approach may complement conventional methods that suffer from limited mass resolution and usually require extensive sample preparation.
High resolution mass spectrometry, and particularly Orbitrap based instrumentations, are emerging as powerful technologies for speciation analysis, mainly to collect reliable information on isotope ratios (IRs). During recent years, traditional, stable isotopic systems, namely H, C, N, O and S have been investigated, but we only recently demonstrated that a dedicated complexation procedure followed by collisional dissociation may enable the investigation of metal ion IRs, and particularly lead, employing a standard electrospray ionization source. The procedure has not yet been demonstrated to be applicable to real-world samples. A total of 31 sediment samples from Lake Como were analyzed for lead IRs by both ESI-Orbitrap and Multi collector ICP-MS. Minor modifications to the original ESI-Orbitrap method, including increased ligand concentration, were required due to sample complexity; the simple Standard-Sample Bracketing (SSB) procedure was demonstrated to be effective in correcting the mass bias. Bland-Altman analysis showed no statistically significant differences between the two methods (95% confidence level) for the two isotope ratios 204Pb/206Pb and 207Pb/206Pb, while a small deviation (<2‰) was observed for the 208Pb/206Pb, remaining acceptable for environmental applications. The isotopic data trend identified leaded gasoline as the main contributor to lead contamination in Lake Como during the period 1950-2000. This work presents the first reported application of ESI-Orbitrap-based metal isotopic analysis in complex environmental matrices. Factors influencing accuracy and precision were systematically evaluated, demonstrating robust analytical performance. The results establish the potential of the ESI-Orbitrap approach for determining isotope ratios of metal ions in real-world samples.