Ethylene glycol (EG)-based lubricant was prepared with dissolved organosolv lignin from birch wood (BL) and softwood (SL) biomass. The effects of different lignin types on the rheological, thermal, and tribological properties of the lignin/EG lubricants were comprehensively investigated by various characterization techniques. Dissolving organosolv lignin in EG results in outstanding lubricating properties. Specifically, the wear volume of the disc by EG-44BL is only 8.9% of that lubricated by pure EG. The enhanced anti-wear property of the EG/lignin system could be attributed to the formation of a robust lubrication film and the strong adhesion of the lubricant on the contacting metal surface due to the presence of a dense hydrogen bonding (H-bonding) network. The lubricating performance of EG-BL outperforms EG-SL, which could be attributed to the denser H-bonding sites in BL and its broader molecular weight distribution. The disc wear loss of EG-44BL is only 45.7% of that lubricated by EG-44SL. Overall, H-bonding is the major contributor to the different tribological properties of BL and SL in EG-based lubricants.
Piston rings (PR) are known for almost a quarter of the friction losses in internal combustion engines. This research work aims to improve the tribological performance of PR by a recently developed variant of Diamond-like Carbon (DLC) coatings deposited in a mixture of Ar and Ne plasma atmosphere (Ne-DLC) by high-power impulse magnetron sputtering (HiPIMS). For the benchmark, the widely used Chromium Nitride (CrN) and DLCs deposited in pure Ar plasma atmosphere (Ar-DLC) were used. The tribological tests were performed on a block-on-ring configuration under different lubrication regimes by varying temperatures and sliding speeds. The analysis of the results was performed by Stribeck curves corresponding to each sample. An improvement of the tribological performance was observed for Ne-DLC films by up to 22.8% reduction in COF compared to CrN in the boundary lubrication regime, whereas, for the Ar-DLC film, this reduction was only 9.5%. Moreover, the Ne-DLC films achieved ultralow friction of less than 0.001 during the transition to a hydrodynamic lubrication regime due to better wettability (lower contact angle) and higher surface free energy. Increasing the Ne up to 50% in the discharge gas also leads to an increase of hardness of DLC films from 19 to 24 GPa.
Enhancement of the thermomechanical stability of diamond-like carbon (DLC) coatings is highly demanded by the automotive industry due to graphitization at higher temperatures. This work is devoted to the assessment of the thermomechanical stability of annealed DLC films deposited by increasing Ne up to 50% in high-power impulse magnetron sputtering (HiPIMS) plasma, followed by the evaluation of their tribomechanical properties. The tribological performance of the films was assessed by room-temperature tribological tests after annealing the films, and by high-temperature tribological test at 300 °C in ambient atmosphere. The microstructure and chemical compositions of the films were analyzed, and the hybridization state of the annealed films was determined by x-ray absorption near-edge spectroscopy (XANES). The wear mechanism involved in both high-temperature and annealed films tribological tests with the steel counterpart was the combination of abrasion and adhesion. It was observed that all the films demonstrated stable tribomechanical performance by annealing up to 500 °C, while from 600 °C, the film deposited in pure Ar plasma demonstrated poor tribomechanical performance. In contrast, increasing Ne to 50% in plasma led to an increase in the thermomechanical stability of DLC films to more than 700 °C, and resisting graphitization up to 800 °C.
Increasing the operating temperature of internal combustion engines (ICE) to enhance their thermodynamic efficiency is a cause for concern about the thermomechanical stability of diamond-like carbon (DLC) coatings for application in ICE. Deep oscillation magnetron sputtering (DOMS), a variant of high-power impulse magnetron sputtering (HiPIMS) is a promising deposition technique that has been used to deposit DLC films with considerably better mechanical and tribological properties than conventional sputtering methods at room temperature. In the present work, the thermomechanical stability of non-hydrogenated DLC films deposited by HiPIMS-DOMS with different ratios of Ar and Ne in the discharge gas was evaluated by applying mechanical and tribological tests as-deposited and after annealing up to 700 ºC. Moreover, the structure of the films in as-deposited and post-annealed states was assessed by the process gas content in the films and was characterized by electron microscopy and ion beam analysis (IBA) techniques. It was observed the film that deposited in pure Ar plasma had a complete Ar effusion and low-density microstructure after annealing up to 700 ºC which caused low hardness and poor tribological performance of the film. On the other hand, the film that was deposited with 50% Ne in the discharge gas maintained its density after annealing up to 700 ºC and retained its hardness at about 20 GPa with a favorable tribological performance.