In this paper, evolution of microstructures, electrical properties and defects of the double Schottky barrier during the sintering process were investigated by quenching ZnO varistor ceramics at different sintering stages. It was found that morphology of the samples changed little when the temperature was below 800 °C. Remarkable enhancement of the Schottky barrier height and electrical properties took place in the temperature range between 600 °C and 800 °C. The Bi-rich intergranular layer changed from β phase to α phase. The interfacial relaxation at depletion/intergranular layers became detectable in the samples. Meanwhile, a distinct relaxation loss peak from electron trapping of interface states was observed instead of two dispersed ones. It indicated that the differences among the Schottky barriers in ZnO varistor ceramics became smaller with the process of sintering, which was also supported by the admittance spectra. In addition, oxygen vacancy was found more sensitive to the sintering process than zinc interstitial. The results could provide guidance for fine manipulating the Schottky barrier and its underlying defect structures by optimizing sintering process.
In this paper, based on insulation coordination and simulation, a lightning protection composite insulator is proposed, made up of an insulation part and an arrester part connected in series, whose length is close to that of the standard composite insulator, which met the window size requirements of the tower. The arrester part contains zinc oxide resistors and an internal core rod, which has good explosion-proof performance and tensile strength, in the meantime overcomes the problem that arresters cannot bear the tensile load of transmission lines. Electrical simulations and experiments have shown that the shielding failure current can be released through the proposed lightning protection insulator to the ground and the counterattack current can be prevented from entering the line. The dry-arc distances of the arrester part and the insulation part are 2.4 and 2.2 m respectively, and the grading ring distance is 1.8 m. The maximum AC withstanding voltage reaches 700 kV, and the switching overvoltage impulse withstanding voltage reaches 1200 kV. The proposed insulator can prevent lightning accidents from happening. Moreover, its length, tensile load, and installation mode are the same as existing line insulators, which has the advantages of low cost and ease of installation and maintenance.
4 November 2022 in IEEE Transactions on Dielectrics and Electrical Insulation
The impact of high-energy electron beam irradiation on silicone rubber composite insulator is investigated in this article. It was discovered that as the irradiation dose increased, the related properties of silicone rubber increased first and then decreased, with the static contact angle increasing to 111.8°, the tensile strength increasing to 4.59 MPa, the tear strength increasing to 26.8 kN/m, and the crosslinking density increasing to $7.09\times 10^{-{4}}$ mol/cm3, but the elongation decreasing. SEM observation revealed that silicone rubber was more compact after irradiation. attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS) studies revealed that when the irradiation dose increased, the irradiation of silicone rubber shifted from crosslinking to degradation, and a new Si(−O)4 structure formed. Considering comprehensive performances, 40–50 kGy is the optimal irradiation dose. This article can provide support for understanding the irradiation modification of silicone rubber materials for composite insulator and also guide the preparation method of new silicone rubber.
Metal-oxide arresters (MOAs) are used to absorb the electrical energy resulting from overvoltages in power systems. However, temperature rises caused by the absorbed energy can lead to the electrothermal failure of MOAs. Therefore, it is necessary to analyze the electric and thermal characteristics of MOAs. In this paper, in order to study the electric and thermal characteristics of MOAs under power frequency voltage, an improved electrothermal model of an MOA is presented. The proposed electrothermal model can be divided into an electric model and a thermal model. In the electric model, based on the conventional MOA electric circuit, the effect of temperature on the voltage–current (V–I) characteristics of an MOA has been obtained. Using temperature and applied voltage as input data, the current flows through the MOA can be calculated using the artificial neural network (ANN) method. In the thermal model, the thermal circuit of a MOA has been built. The varistor power loss obtained from the electric model is used as input data, and the temperature of the zinc oxide varistors can be calculated. Therefore, compared with the existing MOA models, the interaction of leakage current and temperature can be considered in the proposed model. Finally, experimental validations have been done, and the electrothermal characteristics of an MOA have been studied by simulation and experimental methods. The electrothermal model proposed in this paper can assist with the prediction of the electric and thermal characteristics of MOAs.
This paper investigated the effects of sintering temperature on the microstructure and electri-cal properties of ZrO2-doped zinc oxide (ZnO) varistor ceramics. The results show that, the additive ZrO2 exists as independent second phase between ZnO grains, which can limit the growth of ZnO grains and im-prove the voltage gradient. With the increasing of ZrO2, the content of extrinsic elements (Mn, Sb, Co, Cr) in the grain boundary layers tends to increase first and then decease. When ZrO2 content is more than 1.0mol%, the electrical performance of ZnO varistors decreases sharply. With the increasing of sintering temperature, the ZnO grain size increases and the voltage gradient decreases. When the sintering tempera-ture is larger than 1200°C, more monoclinic ZrO2 phase transformed into cubic phase, and more micropores are generated, causing the non-linear coefficient to decrease and the residual voltage ratio and leakage cur-rent to increase. With a sintering temperature of 1150°C and a ZrO2 content of 1.0mol%, the ZnO varistors can reach the overall optimum electric performance, exhibiting a breakdown voltage of E1mA=420V/mm, a nonlinear coefficient of α=58, a residual voltage ratio of CR=1.87, and a leakage current of IL=4µJA. The studies in this paper can give reference for the development of high quality ZnO arresters.
The linear velocity at the tip of large wind turbine blades can reach 100 m/s, generating static electricity through friction with airborne particles. However, the accumulation characteristics of precipitation static on the blade surface and its impact on the lightning attachment characteristics are rarely reported. The authors constructed a platform for measuring charges on rotating wind turbine blades and employed the electrostatic probe method to obtain the accumulation characteristics of surface charges under different environmental conditions. The experimental results show that positive charges accumulate on the blade surfaces, peaking at 0.69 μC/m 2 under experimental conditions. The charge density is positively correlated with airborne particle concentration and blade rotation speed, while it is negatively correlated with relative air humidity. Additionally, the authors developed a model of the electric field distribution on wind turbine blades considering the effects of precipitation static. Simulation results indicate that the electrostatic field induced by precipitation static weakens the field strength in the vicinity of receptors, reaching a minimum of only 38% of the original strength, thereby increasing the probability of lightning protection failure. The findings provide an effective supplement to the lightning attachment mechanism of rotating wind turbine blades.