Florentina Niculescu

Prof. Dr. Florentina Niculescu

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 January 2023 in Crystals
Verified
Journal Article
Open access
PDF file
AMAlecs Matei
Alecs Matei
RTRamona Nicoleta Turcu
Ramona Nicoleta Turcu
IPIon Pencea
Ion Pencea
EHEugen Herghelegiu
Eugen Herghelegiu
MPMircea Ionuţ Petrescu
Mircea Ionuţ Petrescu
FNFlorentina Niculescu
Florentina Niculescu
The main objective of this work was to assess and compare the structure and mechanical properties of the TiN and TiAlN coatings deposited on a new WC-Co tool using the cathodic arc evaporation vacuum deposition (CAE-PVD) technique. The cutting tool was sintered at high temperature and high pressure using a powder tungsten carbide matrix ligated with cobalt (WC-Co). Powdered grain growth inhibitors (TiC, TaC, and NbC) were admixed into the matrix to enhance its strength and to facilitate the adhesion of the Ti base coatings. Detailed scanning electron microscopy with energy-dispersive spectrometry (SEM-EDS) and X-ray diffraction (XRD) analyses were performed, aiming to substantiate the effectiveness of the inhibitor additions. XRD data were thoroughly exploited to estimate the phase contents, average crystallite sizes (D), coating thicknesses (t), texture coefficients (Thkl), and residual stress levels (σ). Atomic force microscopy (AFM) was used to calculate the average roughness (Ra) and the root mean square (Rq). The microhardness (µHV) was measured using the Vickers method. The TiAlN characteristics (D = 55 nm, t = 3.6 μm, T200 = 1.55, µHV = 3187; σ = −2.8 GPa, Ra = 209 nm, Rq = 268 nm) compared to TiN ones (D = 66 nm, t = 4.3 μm, T111 = 1.52, µHV = 2174; σ = +2.2 GPa, Ra = 246 nm, Rq = 309 nm) substantiate the better adequacy of the TiAlN coating for the WC-Co substrate. The structural features and data on the TiN and TiAlN coatings, the tool type, the different stress kinds exerted into these coatings, and the way of discrimination of the coating adequacy are the novelties addressed in the paper.

19 January 2023 in Journal of Environmental Management
Verified
Journal Article
Open access
IPIon Pencea
Ion Pencea
RTRamona Nicoleta Turcu
Ramona Nicoleta Turcu
APAlina Cristina Popescu-Argeș
Alina Cristina Popescu-Argeș
ATAndrei Lucian Timiș
Andrei Lucian Timiș
APAdrian Priceputu
Adrian Priceputu
FNFlorentina Niculescu
Florentina Niculescu
The scope of this study consists of setting up of an integrated cost-effective sampling & laboratory analyses procedure which delineates sampling, sub-sampling and analytical uncertainties in case of fine-grained extractive waste deposits. This procedure is designed to support the decision makers towards fine-grained waste deposits upcycling and land reclamation. This procedure consists of a balanced replicated sampling design (BRSD) coupled with a three split levels ANOVA data processing. The paper provides the readership with the mathematical backgrounds of the three split level ANOVA analysis (3L-ANOVA) and an Excel algorithm for its implementation. Also, the paper presents an example of implementation of the developed methods in the case of a Romanian iron ore tailings (IOT) old pond. The findings of the paper consist of: a) argues, based on OM, SEM-EDS, XRFS and XRD observations, that classical TOS is ineffective for fine-grained waste deposits; b) BRSD in conjunction with 3L-ANOVA analysis is the only approach fit for reliable characterization of the fine-grained stockpiles; c) sampling uncertainty is the critical factor of the uncertainty budget of the analyte concentration; d) Lilliefors approach is adequate for the hypothesis testing where or not the measurand is normal distributed; e) The outcomes of the BRDSD&3L-ANOVA investigations carried on Teliuc tailings, estimated at circa 5.5* 106 m3, consist mainly of mineral quantification at lot level i.e. quartz ∼54% (±7%), hematite ∼15% (±3%), calcite ∼11% (±3%), MgO 3% (±1%), Al2O3 9% (±2%). The concentrations of some CRMs like Ti, V, Ba, Y, W were found at ACE limits and their associated relative expanded uncertainties overpass 50%. Thus, the expanded uncertainties clearly depict the reliability of acquired data for the decision makers regarding waste valorization. f) The IOT into Teliuc can be upcycled as minerals for cement and ceramic industries as well as for geopolymer manufacture. Also, IOT can be downcycles as filler in road construction and mine closure. Finally, the Teliuc yard can be rehabilitated with zero-waste left behind. The data exactness provided by this procedure can be increased to any desirable level through increasing the number of collected items, but the cost of sampling and analyses increases proportionally. In such circumstances, the posted approach can be tailored at the stakeholder request as to safely underpin the decision to turn finegrained by-products into valuable secondary resources, facilitating a greater circularity of the mining industry.

18 August 2025 in Metals
Verified
Journal Article
Open access
PDF file
AIAndrei-Alexandru Ilie
Andrei-Alexandru Ilie
FNFlorentina Niculescu
Florentina Niculescu
GIGheorghe Iacob
Gheorghe Iacob
IPIon Pencea
Ion Pencea
Florin MiculescuFlorin Miculescu
Florin Miculescu
CUConstantin Ungureanu
Constantin Ungureanu
The Bi-Sn, Bi-Sn-Ag, and Bi-Sn-Sb solder alloy systems represent lead-free, environmentally friendly alternatives for reliable electronic assembly. These alloys comply with increasingly strict environmental and health regulations, while offering low melting points suitable for soldering temperature-sensitive components. Microstructural analysis revealed distinct phase segregation in all alloys, with Sb promoting coarse Sn2Sb3 intermetallic compounds and Ag inducing fine needle-like Ag3Sn precipitates. Eutectic refinement and compositional contrast were confirmed by SEM-BSE and EDS mapping. Vickers microhardness measurements revealed increased hardness in Sb- and Ag-modified Bi–Sn alloys, with Ag3Sn dispersion yielding the highest strengthening effect, indicating enhanced mechanical potential. This study also reports the thermal and electrical conductivities of Bi60Sn40, Bi60Sn35Ag5, and Bi60Sn35Sb5 alloys over the 25–140 °C range. Bi60Sn40 showed an increase in thermal conductivity across the full temperature range from 16.93 to 26.93 W/m·K, while Bi60Sn35Ag5 reached 18.28 W/m·K at 25 °C, and Bi60Sn35Sb5 exhibited 13.90 W/m·K. These findings underline the critical influence of alloying elements on microstructure, phase stability, and thermophysical behavior, supporting their application in low-temperature soldering technologies.

7 October 2024 in Materials
Verified
Journal Article
Open access
PDF file
GIGheorghe Iacob
Gheorghe Iacob
VGValeriu Gabriel Ghica
Valeriu Gabriel Ghica
FNFlorentina Niculescu
Florentina Niculescu
MPMircea Ionuţ Petrescu
Mircea Ionuţ Petrescu
AVAna Vasile
Ana Vasile
The experimental research was focused on the investigation of valuable material from spent Ni-MH type AA batteries, namely the metal grid anodes and the black mass material (anode and cathode powder). The materials of interest were analyzed by X-ray fluorescence spectroscopy (XRF), ICP-OES (inductively coupled plasma optical emission spectrometry), optical microscopy, scanning electron microscopy (SEM), energy-dispersive X-ray analysis (EDX), electron backscatter diffraction (EBSD), and X-ray diffraction (XRD). The analyzed grids have a high Fe content, but some of them correspond to the Invar alloy with approx. 40% Ni. In the black mass material, round particles and large aggregations were observed by SEM analysis, showing a high degree of degradation. The XRD analysis reveals the presence of only three compounds or phases that crystallize in the hexagonal system: La0.52Ce0.33Pr0.04Nd0.11Co0.6Ni4.4, Ni(OH)2, and La5Ni19. The obtained results provide useful and interesting information that can be used for further research in the recycling and economic assessment of metals from spent Ni-MH batteries.

29 March 2024 in Materials
Verified
Journal Article
Open access
PDF file
FNFlorentina Niculescu
Florentina Niculescu
IPIon Pencea
Ion Pencea
GIGheorghe Iacob
Gheorghe Iacob
MGMIHAI GHITA
MIHAI GHITA
MSMariana Mirela Stanescu
Mariana Mirela Stanescu
AIAndrei-Alexandru Ilie Andrei-Alexandru Ilie
Andrei-Alexandru Ilie Andrei-Alexandru Ilie
Properties such as lower melting temperature, good tensile strength, good reliability, and well creep resistance, together with low production cost, make the system Bi-Sn an ideal candidate for fine soldering in applications such as reballing or reflow. The first objective of the work was to determine the thermodynamic quantities of Bi and Sn using the electromotive force measurement method in an electrolytic cell (Gibbs’ enthalpies of the mixture, integral molar entropies, and the integral molar excess entropies were determined) at temperatures of 600 K and 903 K. The second objective addressed is the comprehensive characterization of three alloy compositions that were selected and elaborated, namely Bi25Sn75, Bi50Sn50, and Bi75Sn25, and morphological and structural investigations were carried out on them. Optical microscopy and SEM-EDS characterization revealed significant changes in the structure of the elaborated alloys, with all phases being uniformly distributed in the Bi50Sn50 and Bi75Sn25 alloys. These observations were confirmed by XRD and EDP-XRFS analyses. Diffractometric analysis reveals the prevalence of metallic Bi and traces of Sn, the formation of the Sn0.3Bi0.7, Sn0.95Bi0.05 compounds, and SnO and SnO2 phases.

1 January 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
IPIon Pencea
Ion Pencea
RTRamona Nicoleta Turcu
Ramona Nicoleta Turcu
APAlina Cristina Popescu-Arges
Alina Cristina Popescu-Arges
ATAndrei Lucian Timis
Andrei Lucian Timis
APAdrian Priceputu
Adrian Priceputu
FNFlorentina Niculescu
Florentina Niculescu
This work aims at mitigating the sampling bottleneck for fine-grained waste streams through a new integrated sampling and laboratory analyses procedure which delineates sampling, sub-sampling and analytical uncertainties. The developed procedure consists of a balanced replicated sampling design (BRSD) coupled with a three split levels ANOVA data processing. The paper provides the readership with the mathematical backgrounds of the three split level ANOVA analysis (3L-ANOVA) and an Excel algorithm for its implementation. Also, the paper presents an example of implementation of the developed methods in the case of an Romanian iron ore tailings (IOT) old pond.The findings of the paper consist of:a) argues, based on OM, SEM-EDS, XRFS and XRD observations, that TOS is ineffective for fine-grained waste deposits; b) BRSD in conjunction with 3L-ANOVA analysis is the only approach fit for reliable characterization of the fine-grained stockpiles; c) sampling uncertainty is the critical factor of the uncertainty budget of the analyte concentration;d) Lilliefors approach is adequate for the hypothesis testing where or not the measurand is normal distributed; e) BRSD&3L-ANOVA delineates sampling, sub-sampling and analytical uncertainties that quantify the distribution heterogeneity of the targeted mineral across the tailings yard. f) The outcomes of the BRDSD&3L-ANOVA investigations carried on Teliuc tailings, estimated at circa 5.5* 106 m3, let us consider that this IOT can be upcycled as minerals for cement and ceramic industries as well as for geopolymer manufacture. Also, IOT can be downcycles as filler in road construction and mine closure. Finally, the Teliuc yard can be rehabilitated with zero-waste left behind. The data exactness provided by this procedure can be increased to any desirable level through increasing the number of collected items, but the cost of sampling and analyses increases proportionally. In such circumstances, the posted approach can be tailored at the stakeholder request as to safely underpin the decision to turn fine-grained by-products into valuable secondary resources, facilitating a greater circularity of the mining industry.