This paper presents a low-power and scaling-friendly noise-shaping (NS) SAR ADC. Instead of using operational transconductance amplifiers that are power hungry and scaling unfriendly, the proposed architecture uses passive switches and capacitors to perform residue integration and realizes the path gains via transistor size ratios inside a multi-path dynamic comparator. The overall architecture is simple and robust. Since the noise transfer function is set by component ratios, it is insensitive to process, voltage, and temperature (PVT) variations. Besides the proposed architecture, this paper also presents two new circuit techniques. A tri-level voting scheme is proposed to reduce the comparator noise. It outperforms the majority voting technique by exploiting more information in the comparator output statistics and providing an extra decision level. A dynamic multi-phase clock generator is also proposed to guarantee non-overlapping and support an arbitrary number of phases. A prototype 9-bit NS-SAR ADC is fabricated in a 40-nm CMOS process. It consumes 143 μW at 1.1 V while operating at 8.4 MS/s. Taking advantage of the second-order NS, it achieves a peak SNDR of 78.4 dB over a bandwidth of 262 kHz at the oversampling ratio of 16, leading to an SNDR-based Schreier figure of merit (FoM) of 171 dB.
1 January 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
This article presents a 7-bit 900-MS/s multi-bit/cycle successive approximation register (SAR) analog-to-digital converter (ADC) with background offset calibration. Unlike prior works that adopt either four capacitive DACs (CDACs) or interpolated resistive DAC to enable 3-bit/cycle operation, the proposed technique uses only two CDACs to realize the same functionality. The number of CDACs is reduced by embedding gain inside the two-path comparators, resulting in reduced power, area, and input loading. In addition, the built-in redundancy relaxes the accuracy requirements for DAC settling and comparators. On-chip background offset calibration with narrow pulse charge sharing is used to further improve the ADC linearity. The prototype fabricated in 40-nm LP CMOS achieves an SNDR of 39.7 dB at Nyquist input and consumes 2.6 mW including on-chip calibration, leading to a Walden FoM of 36.6 fJ/conversion-step.
20 April 2021 in IEEE Journal of Solid-State Circuits
This article proposes a fully dynamic, low-power, wideband, time-interleaved (TI), noise-shaping (NS) successive-approximation-register (SAR) analog-to-digital converter (ADC) based on the cascade of integrators with feedforward (CIFF) architecture. Both the interleaving operation and the loop filter are implemented by using the fully passive switched-capacitor circuits. The feedforward summation is realized by a multi-path dynamic comparator. The overall noise transfer function (NTF) is highly robust against process, voltage, and temperature (PVT) variations since the NTF is determined by device ratios. This allows the NTF zeros to be close to 1, with a good NS effect. Compared with a recently published TI NS SAR based on the error-feedback (EF) architecture, this work does not need a static amplifier, thus leading to the fully dynamic operation. Meanwhile, it eliminates the dependence of NTF on the PVT-sensitive amplifier gain. Implemented in a 40-nm CMOS process, the prototype ADC achieves an SNDR of 69.1 dB, a bandwidth of 50 MHz, and a power consumption of 8.5 mW under a 1.1-V supply, leading to a Walden FoM of 36.3 fJ/conv.-step.
14 January 2020 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a novel pico-watt voltage reference (VR) circuit whose power consumption is well controlled at high temperature. Unlike a traditional pico-watt VR circuit whose power consumption increases exponentially with temperature, the power consumption in this article increases linearly with temperature, thus saving much energy at high temperature. It generates the reference voltage through a 2-transistor (2-T) structure and a current generator to well control the current versus temperature. In the current generator, a gate leakage transistor replaces a huge resistor, thus saving 4-mm² area. Fabricated in a 0.13-μm CMOS process, this VR circuit generates a reference voltage of about 560 mV and shows an average temperature coefficient (TC) of 18.4 ppm/°C after trimming across -25 °C to 85 °C and a line sensitivity (LS) of 0.15%/V, while consuming 20 pW at 1-V VDD and 27 °C. The power consumption at 3.3-V VDD and 85 °C is 114 pW, which is at least two times smaller than reported in state-of-the-art work at high temperature. The core area is 0.003 mm².
10 June 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This brief presents a novel timing mismatch background calibration algorithm for time-interleaved (TI) analog-to-digital converters (ADCs). It can calibrate an arbitrary number of channels with an arbitrary input frequency. It also increases the calibration accuracy by applying the autocorrelation functions with an expanded interval. Besides, the proposed algorithm effectively prevents the small derivative values in the correlation difference from degrading the skew estimation accuracy. Compared to prior works on calibration, this work has at least five times better detection accuracy when the frequency of the input signal is close to the Nyquist frequency. This is without the need for calculating the high-order statistics. Finally, we simulate a four-channel 12-bit TI ADC with non-ideal effects added. Simulation results show that the proposed algorithm increases the signal to noise-plus-distortion ratio (SNDR) and spurious-free dynamic range (SFDR) from 35.5 and 40.0 dB to 63.3 and 84.6 dB, respectively, when the input frequency is close to the Nyquist frequency.