Developing sustainable TiO2-based photocatalysts for environmental remediation is an increasingly significant area of research. However, a limited understanding of the long-term ecological impact of these photocatalysts poses a barrier to their practical and industrial-scale applications. To address this challenge, this work employed a green synthesis approach to prepare an Ag/TiO2 photocatalyst designed to improve environmental compatibility and enhance efficiency in pollutant degradation. Ag/TiO2 was synthesized using mushroom biomass as a natural capping to evaluate its effectiveness in the degradation of ciprofloxacin (CIP) and azo Carmine G dye (ACGD). The mushroom biomass served as a renewable cost-effective support for Ag incorporation, while the Ag modification of TiO2 could enhance the photocatalyst’s performance. Structural, chemical, and morphological characterization techniques were applied and showed that the Ag/TiO2 particles consisted of irregularly shaped nanoparticles. The CIP removal reached 82.46% after 300 min and ACGD removal efficiency went up to 83.64%. The enhanced performance is attributed to the unique electronic and structural properties of Ag-modified TiO2. This study highlights the potential of Ag/TiO2 synthesized via green methods as a high-performance photocatalyst for the effective remediation of pharmaceutical and dye pollutants in wastewater treatment applications.
Debonding of the primary anode caused by anodic acidification is one of the major failure modes of the impressed current cathodic protection (ICCP) system in reinforced concrete structures. This study used 3D micro X-ray computed tomography (μ-XCT) to monitor the in situ evolution of the anodic acidification-affected zone. Samples were scanned after 0 to 40 days of the accelerated anodic acidification test. The anodic acidification-affected zone was identified in μ-XCT images using the gray level segmentation method. The total volume of this zone was measured using the 3D reconstruction method. It was found that detailed 3D information can be extracted using the 3D reconstruction method. The spatial heterogeneity was analyzed using this reconstructed volume information. The Faraday efficiency was calculated and found to increase after 20 days of operation. It was also found that the affected zone was proportional to the input electrical energy. The proposed model is useful for estimating the durability of an ICCP system.
Reinforced concrete (RC) beams strengthened with carbon-fabric-reinforced cementitious matrix (CFRCM) systems have shown potential for restoring flexural performance, yet their effectiveness under different corrosion levels remains insufficiently understood. This study presents a numerical investigation of the flexural behaviour of simply supported RC beams externally strengthened with CFRCM plates. Refined finite element models (FEMs) were developed by explicitly incorporating the steel–concrete bond-slip behaviour, the carbon fabric (CF) mesh–cementitious matrix (CM) interface, and the CFRCM–concrete substrate interaction and were validated against experimental results in terms of failure modes, load–deflection responses, and flexural capacities. A parametric study was then conducted to examine the effects of CFRCM layer number, steel corrosion level, and longitudinal reinforcement ratio. The results indicate that the baseline flexural capacity can be fully restored only when the corrosion level remains below approximately 15%; beyond this threshold, none of the CFRCM configurations achieved full recovery. The influence of the reinforcement ratio was found to depend on corrosion severity, while increasing CFRCM layers enhanced flexural performance but exhibited saturation effects for thicker configurations. In addition, corrosion level and CFRCM thickness jointly influenced the failure mode. Comparisons with design predictions show that bilinear CFRCM constitutive models are conservative, whereas existing FRP-based design codes provide closer agreement with numerical and experimental results.
This study systematically investigates the tensile property degradation of Carbon Fabric-Reinforced Cementitious Matrix (CFRCM) composites under anodic polarization, explicitly comparing the effects of three standard-required electrolyte environments (NACE/ISO). CFRCM specimens were polarized for 20 days at current densities of 200 and 400 mA/m2 in NaCl, NaOH, and simulated concrete pore solutions. Results reveal that anodic polarization significantly reduces peak tensile strength and post-cracking stiffness, with degradation severity dependent on the electrolyte type (NaCl > NaOH > Pore Solution). Crucially, comparative analysis demonstrates that the strength degradation of carbon fiber bundles embedded in the mortar matrix is more pronounced than that of bare bundles. This work provides essential durability data for CFRCM composites for integrated ICCP-Structural Strengthening systems.
12 October 2025 in Russian Journal of Physical Chemistry B
This study introduces physicochemical analyses of Melaleuca leucadendra leaf essential oil (MLEO), followed by a study of its application to prepare novel hydrophobic and antibacterial textiles. This chemical strategy is based on incorporating Melaleuca leucadendra leaf essential oil (MLEO) into cotton fabrics using microencapsulation techniques. The utilized MLEO was investigated via Gas Chromatography-Mass Spectrometry (GC-MS) analysis and identified 37 bioactive compounds in MLEO and carene was found as the predominant antimicrobial agent. The successful microencapsulation of MLEO was indicated via Differential Scanning Calorimetry (DSC). Surface characterization using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS) revealed a uniform microcapsule distribution and the existence of function groups of MLEO with the fabric matrix was indicated via Fourier Transform Infrared Spectroscopy (FT-IR). The contact angle of the modified cotton fabrics was checked and indicated the hydrophobic characteristics. Additionally, antibacterial activity was investigated against Staphylococcus aureus, and promising antibacterial properties were obtained. Therefore, microencapsulation could be used to prepare novel antibacterial and hydrophobic cotton fabrics after modification by essential oil.