In this article, a numerical investigation of the effect of a miniaturized five-hole probe downstream of a transonic low-pressure turbine vane row is presented. First, a numerical calibration of the probe was performed in uniform flow conditions, as is the case for any traditional calibration, for a wide range of Mach number, yaw angle, and pitch angle conditions. The effect of the probe on the general flow field throughout the turbine vane segments was then evaluated by performing a comparison between a setup with vanes only (no probe) and with vanes and probes. It was found that, as the probe traverses downstream the vane, the probe impact on the vane isentropic Mach number depends on the probe circumferential position. The highest impact was observed when the probe is located at the upper mid-passage (θ = 0.5), consisting of a relatively small reduction of the isentropic Mach number on the vane suction side of just 0.02. To assess the accuracy of the quantities “measured” by the probe, the probe-determined flow field was compared to the flow field of the vanes-only setup. A nonnegligible modification of the probe-determined local distributions of Mach number, yaw angle, and pitch angle is revealed with respect to the undisturbed flow. Further investigation involving stagnation point tracking showed that the artificial high circumferential variation of the yaw angle is not caused by a modification of the vane outlet flow angle, but is induced by nonuniform flow conditions downstream of the vanes. With knowledge of the above, a two-step correction is used to account for the effects of the nonuniformity of the flow, and its impact is evaluated on 2D and 3D flow regions. A significative effect of the correction was found on the probe-determined yaw angle, in which the difference from the vanes-only data was reduced to below 1 deg, except near the endwalls where larger discrepancies remain due to probe–endwall interactions. A shortfall of the correction was instead observed on the probe-determined Mach numbers. Finally, the pitch-wise averaged quantities were evaluated. It was observed that the highest differences between probe-determined and undisturbed data occur where radial gradients of total pressure are stronger and that the two-step correction had almost negligible impact on the pitch-wise averaged quantities.

The purpose of the paper is to characterize the aerodynamic behavior of a rotor-downstream hub cavity rim seal in a high-pressure turbine (HPT) stage. The experimental data are acquired in the Transonic Test Turbine Facility at the Graz University of Technology: the test setup includes two engine-representative turbine stages (the last HPT stage and first LPT stage), with the intermediate turbine duct in between. All stator-rotor cavities are supplied with purge flows by a secondary air system, which simulates the bleeding air from the compressor stages of the real engine. The HPT downstream hub cavity is provided with wall taps and pitot tubes at different radial and circumferential locations, which allows the performance of steady pressure and seed gas concentration measurements for different purge mass flows and HPT vanes clocking positions. Moreover, miniaturized pressure transducers are adopted to evaluate the unsteady pressure distribution, and an oil flow visualization is performed to retrieve additional information on the wheel space structures. The annulus pressure asymmetry depends on the HPT vane clocking, but this is shown to have negligible impact on the minimum purge mass flow required to seal the cavity. However, the hub pressure profile drives the distribution of the cavity egress in the turbine channel. The unsteady pressure field is dominated by blade-synchronous oscillations. No non-synchronous components with comparable intensity are detected.

Aviation accounts for a significant share of global CO₂ emissions, necessitating efficient propulsion technologies to achieve net-zero emissions by 2050. Geared turbofan architectures offer a promising solution by enabling higher bypass ratios and improved fuel efficiency. However, geared turbofans introduce significant aerodynamic and structural challenges, particularly in the low-pressure turbine. Current understanding of high-speed low-pressure turbine behavior under engine-representative conditions is limited, especially regarding unsteady wake interactions, secondary flows, and compressibility effects. To address these gaps, this work presents a novel test case of high-speed low-pressure turbines, the SPLEEN C1. The test case and experimental methodology are depicted. The study includes the commissioning and characterization of a transonic low-density linear cascade capable of testing quasi-3D flows. The rig’s operational stability, periodicity, and inlet flow characterization are assessed in terms of loss and turbulence quantities to ensure an accurate representation of engine conditions. These findings provide a validated experimental platform for studying complex flow interactions in high-speed low-pressure turbines, supporting future turbine design and efficiency advancements.

This paper presents the commissioning of a newly designed High-Speed Low-Pressure Turbine (LPT) stage, operating at transonic exit Mach numbers and low Reynolds numbers, typical of modern geared turbofan (GTF) applications. The work falls within the scope of the Clean Sky 2 project SPLEEN (Secondary and Leakage Flow Effects in High-speed Low-pressure Turbines), which consists of an extensive experimental characterization of LPTs for GTFs. Geometries and measurements will constitute a valuable open-access database for the validation of simulation methods and data analysis tools. At first, the characteristics of the research turbine are illustrated. The LPT stage is designed with an equal number of stationary vanes and shrouded rotor blades. The upstream and downstream hub cavities are purged and feature engine-realistic rim seals. The nominal operating condition of the stage is reported, along with a set of off-design conditions, obtained by varying rotor speed and purge mass flows. The second part of the paper describes the substantial revamping of the CT3 large-scale compression tube at Von Karman Institute for Fluid Dynamics, traditionally employed for high-pressure turbine testing, now adapted to host a high-speed LPT stage. The third section is an overview of the time-averaged and fast-response instrumentation. The test article is heavily instrumented, to maximize the amount of acquired data, while minimizing the number of blowdown tests. The dataset for each operating conditions includes aerothermal measurements in the annulus flow, in the hub cavities and in the shroud labyrinth seal. In addition, this section presents the design of an in-house traversing system for continuous probe traversing during the test. Finally, the outcome of the commissioning phase is discussed, with particular emphasis on the operating conditions stability, as well as on the inlet and cavity injection uniformity. The commissioning of a traversing system for continuous probe traversing during the short-duration test is also discussed.

This paper investigates the influence of combustor temperature non-uniformities on modern engine turbine center frames (TCFs). Due to their position in an engine, coupled with the trends of more aggressive designs, increased turbine inlet temperatures (TIT), and utilization of lean-burn combustors, turbine center frames are exposed to even higher temperatures and non-uniform temperature flow fields. These temperature non-uniformities, or hot streaks (HS), were previously studied at the combustor—high-pressure turbine (HPT) interface, but there is no available research in the open literature that clarifies their influence on the TCF performance. A new test bench, designed specifically for fundamental research on hot streaks, was set up at the Institute for Thermal Turbomachinery and Machine Dynamics at the Graz University of Technology, Austria. The test bench features a 90 deg sector cascade of an engine representative TCF geometry, equipped with a hot streak generator and a flow conditioning grid. Experimental data were gathered by means of five-hole probe area traverses at the TCF inlet and outlet planes. Two individual clocking positions of hot streaks were investigated, as well as three different radial positions for each of the clocking scenarios. Hot streaks were injected upstream of the flow conditioning grid, generating a representative temperature ratio at the TCF inlet plane. Results show that the hot streaks have migrated radially outwards and are characterized by different temperature distributions, depending on the injection position. An increase in pressure loss and thermal loading of the strut and the shroud are observed.

High-speed, low-pressure turbines in geared turbofans operate at transonic exit Mach numbers and low Reynolds numbers. Engine-relevant data remain scarce. The SPLEEN C1 linear cascade was investigated at $M_{\mathrm{out}}=0.70–0.95$ and $R{e}_{\mathrm{out}}=\mathrm{65,000}–\mathrm{120,000}$ under steady inlet flow. Experiments were combined with 2D RANS and MISES, including transition modeling and inlet-turbulence decay calibrated to measurements. Results are consistent with conventional LPT behavior: loss decreased with increasing Mach and Reynolds numbers, except when shocks interacted with the blade boundary layer ($M\approx 0.95$). Profile loss dropped by $23\%$ from $M=0.70$ to $0.95$ at $Re=\mathrm{70,000}$, as well as by $19\%$ at $M=0.80$ when open separation is suppressed. Secondary loss decreased by up to $25\%$ at $Re=\mathrm{70,000}$ and showed weak sensitivity to the Reynolds number. A coupled loss model predicted profile loss with a root-mean square error of 4.7%. Secondary-loss modeling reproduced global trends: separating endwall dissipation from mixing kept errors within $\pm 10\%$ for most cases, but accuracy degraded near the shock–boundary layer interaction case and at the highest Reynolds number. Mixing dominated endwall loss (∼75%), with the passage vortex contributing ∼50% (±10%) of the mixing component.