In the modern world, issues related to the use of alternative fuels are becoming increasingly pressing. These fuels offer the potential to achieve significantly improved environmental and technological performance. Currently, among such fuels, biodiesel, ammonia, LPG, and hydrogen are considered the most promising options. LPG and hydrogen exhibit a high Lower Heating Value (LHV) and have a relatively low environmental impact. This article investigates the combustion of hydrogen-LPG mixtures in a diffusion burner. The main parameters under study include the proportion of hydrogen in the fuel, equivalence ratio, and vane angle. The analyzed parameters encompass NOx and CO concentrations. The studies have demonstrated that the addition of hydrogen can reduce greenhouse gas emissions, as the combustion product is clean water. The primary focus of this research is the examination of combustion processes involving flow swirl systems and alternative fuels and their mixtures. The studies indicate that flame stabilization is significantly influenced by several factors. The first factor is the amount of hydrogen added to the fuel mixture. The second factor is the degree of mixing between the fuel and oxidizer, along with hydrogen. Lastly, the equivalence ratio plays a crucial role. As the studies have shown, the maximum stabilization for a speed of 5 m/s is achieved at an angle of 60° and a hydrogen fraction of 40%, resulting in φ_LBO = 0.9. This represents an 8.0% improvement in stabilization compared to the baseline mode, primarily due to the substantial proportion of hydrogen. An analysis of flame photographs reveals that as the twist angle increases, a recirculation zone becomes more apparent. Increasing the blade angle and incorporating hydrogen leads to a reduction in CO concentrations in the exhaust gases. The analysis indicates that increasing the hydrogen proportion to 50%, compared to the absence of hydrogen, results in a 30% decrease in CO concentration. In our case, for the option φ = 0.3 and blade angles of 60°, the reduction in CO concentration was 28.5%. From the authors’ perspective, the most optimal vane angle is 45°, along with a hydrogen fraction of 30–40%. With these parameters, it was possible to achieve concentrations of NOx = 17–25 ppm, φ_LBO = 0.66, and CO = 130–122 ppm.

The global shift toward renewable fuels and the reduction in anthropogenic environmental impact have become increasingly critical. However, the current challenges in fully transitioning to environmentally friendly fuels necessitate the use of transitional fuel mixtures. While many alternatives have been explored, the combination of hydrogen and LPG appears to be the most practical under the conditions specific to Kazakhstan. This study presents experimental findings on a novel burner system that utilizes the airflow swirl and hydrogen enrichment of LPG. It evaluates the effects of hydrogen addition, fuel supply methods, and swirl intensity—achieved by adjusting the outlet vanes—on flame stabilization as well as NO_x and CO emissions. The results show that the minimum NO_x concentration achieved was 12.08 ppm, while the minimum CO concentration was 101 ppm. Flame stabilization studies indicate that supplying the fuel at the center of the burner, rather than at the base, improves stabilization by 23%. Additionally, increasing the proportion of hydrogen positively affects stabilization. However, the analysis also reveals that, as the hydrogen content in the fuel rises, NO_x concentrations increase. These findings highlight the importance of balancing the hydrogen enrichment, airflow swirl, and fuel supply methods to achieve optimal combustion performance. While hydrogen-enriched LPG offers enhanced flame stabilization, the associated rise in NO_x emissions presents a challenge that requires careful management to maintain both efficiency and environmental compliance.

Reducing the anthropogenic impact on the environment is an increasingly urgent challenge, particularly in the energy and heat generation sectors. This study presents the results of an experimental investigation into the combustion characteristics of four nozzle types in a burner system. The experiments focused on emissions of NOx and CO under varying equivalence ratios. This study presents an experimental investigation of combustion with one swirl-stabilized nozzle and two multihole plates under varying equivalence ratios (φ). The swirl-stabilized configuration produced the highest NOx, reaching 54.4 ppm at φ = 0.9, which we attribute to higher flame temperatures and longer effective residence. In contrast, the multihole plates—122 holes of 1.0 mm and 36 holes of 4.0 mm in a 100 mm insert—exhibited lower NOx and lower temperatures owing to more effective fuel–air mixing. CO showed a strong dependence on both geometry and φ; the lowest levels occurred near φ ≈ 0.9, consistent with optimal combustion. The findings underscore the importance of nozzle geometry and air–fuel ratio in optimizing combustion efficiency and minimizing harmful emissions, providing valuable insights for the development of low-emission combustion systems in modern energy applications.

Currently there are various concepts of heat transfer intensification, on the basis of which methods have been developed to increase the heat transfer coefficient in the channels of heat exchange surfaces, which do not lead to significant additional energy costs for flow movement. The article presents the results of an experimental study on the influence of various types of fins on heat transfer processes and hydraulic resistance. The results obtained show that fins in the form of crosses and triangles are the most efficient in terms of heat transfer. However, they create the greatest hydraulic resistance. The largest value of the Nusselt number is relevant for fins type 5 and 6 due to a more active effect on the core of the flow owing to its shape. Fins 7 and 4 have the minimal influence, since they have the ‘smoothest’ shape. Studies have shown that with Reynolds numbers in the range of 13,000–32,000, fins of type 4 and 7 show the greatest resistance. It is shown that it is possible to switch from pipes without fins to pipes with fins by including the coefficient B in the Nusselt equation having a range of 0.03–0.061. It is shown that under certain conditions, heat transfer when using fins can decrease with increasing Reynolds number.

Biogas, derived from human waste or industrial byproducts, is considered one of the most environmentally acceptable fuels. However, such fuels often exhibit relatively low efficiency, making it essential to develop technologies that facilitate their effective combustion. This article investigates the combustion of biogas with the addition of hydrogen at varying degrees of flow swirling. For this purpose, a burner was used in which methane, hydrogen and CO₂ were mixed in a mixer. The studies revealed that increasing the proportion of hydrogen in biogas leads to an average 15% rise in the NO_x concentration. Additionally, an increase in the degree of swirling has a positive effect on NO_x generation. On the other hand, a higher proportion of hydrogen reduces the concentration of CO in the exhaust gases. The presence of ballast gases, such as CO₂, generally results in relatively low NO_x levels when combined with a high swirling number. The analysis of combustion products for CO₂ indicates a 14% increase in CO₂ proportion. The highest concentrations of CO₂ were observed in biogas with the highest CO₂ ballast content. In terms of reducing NO_x and CO, SW = 1.3 is the most successful. On the other hand, this angle leads to an increase in the CO₂ concentration.

The global push for low-carbon electricity generation has made hydrogen-enriched natural gas an attractive near-term decarbonization option. This paper combines experimental and thermodynamic analyses of H₂–CH₄ combustion in gas turbine combustion chambers. Experiments were conducted on a patented two-stage swirl burner across 240 operating conditions. The effects of hydrogen fraction (γ = 0–40%), swirler vane angle (30°, 45°, 60°), equivalence ratio (φ = 0.17–1.00), and fuel injection strategy were measured against NOx and CO emissions and lean blowout stability. Each 10% increase in hydrogen content raised NOx by 23–24% via the Zel’dovich thermal mechanism, while CO fell by up to 28.5% at φ = 0.3 and 60° due to enhanced OH-radical activity. The minimum recorded NOx was 12.08 ppm (Type 2 injection, 30°, γ = 0%, φ = 0.3). Hydrogen addition improved lean blowout stability by 32–46% per 10% H₂. A parallel thermodynamic analysis showed that integrating an organic Rankine cycle (ORC) and supplementary H₂–CH₄ firing in the heat recovery steam generator cuts specific CO₂ emissions by 7.5–10% and raises net efficiency by 0.79–4.0 percentage points. Critical comparison with 28 published studies identified an optimal operating window: γ = 20–30%, φ = 0.5–0.7, 45° vane angle (SW = 0.8).