Background: Metal lattice structures obtained through Selective Laser Melting may increase the strength-to-weight ratio of advanced 3D printed parts, as well as their damping properties. Recent experimental results showed that AlSi10Mg and AISI 316L lattices are characterized by higher Rayleigh damping coefficients with respect to the fully dense material. However, some unclear or contradictory results were found, depending on the experimental setup adopted for modal analysis. Objective: In this work the influence of the experimental setup when performing modal analysis on different SLM AISI 316L lattice structures was deeply investigated. The study provides a critical comparison of various experimental modal analysis approaches, allowing to evaluate the influence of external damping sources and material internal damping phenomena. Methods: The dynamic behaviour of SLM AISI 316L specimens incorporating lattice structures was estimated by means of pulse testing and sinusoidal excitation through an electromagnetic shaker. The validity of the viscous damping model was assessed by means of sinusoidal excitation with different levels of vibration velocity. Moreover, the influence of experimental setup on modal analysis results was critically evaluated, by considering different actuators, contact and non-contact sensors and boundary/clamping conditions. Results: The classical viscous damping model describes with good approximation the damping properties of SLM lattice structures. When exciting single specimens in free-free conditions, those embedding lattice structure and unmelted metal powder filler were characterized by superior internal damping properties with respect to the specimens incorporating the lattice structure without any filler, which was however more effective than the full density equivalent material. Most of the other experimental setups introduced additional external damping sources, that could alter this important outcome. Conclusions: SLM lattice structures embedded into 3D printed components provide superior damping properties against mechanical and acoustic vibrations and the metal powder filler does significantly enhance such damping capacity. A correct estimation of material internal damping was achieved by applying non-contact sensors and free-free boundary conditions, whereas other experimental setups were partly inadequate.

Chatter vibrations arising during machining operations are detrimental for cutting process performance, since they may cause poor surface quality of the machined part and severe damages to machine tool elements. Passive approaches for chatter suppression are based on the integration of special mechanical components with high-damping properties within the machining system. They represent a good solution to this problem thanks to their intrinsic simplicity. Recently, the application of metallic lattice structures inside 3D printed parts obtained from the Selective Laser Melting technology have proven superior damping properties with respect to the same full density material. Here, this idea is further explored by considering the novel configuration where the unmelted powder grains are retained inside the lattice structure by an external shell, acting as a multiplicity of microscopic mechanical dampers. This concept is applied for passive chatter suppression of thin-walled parts that are of particular relevance for industry. Preliminary experimental investigation was first carried out on simple beam-like specimens, and then on thin-walled benchmarks that were identified through modal analysis and tested under real cutting conditions. The main conclusion is that the novel proposed configuration (lattice plus unmelted powder) has higher damping properties with respect to the full density and lattice alternatives. Accordingly, it may be successfully applied for passive chatter suppression in real machining operations.

The mechanical behavior of the metallic components fabricated by additive manufacturing (AM) technologies can be influenced by adjustments in their microstructure or by using specially engineered geometries. Manipulating the topological features of the component, such as incorporating unit cells, enables the production of lighter metamaterials, such as lattice structures. This study investigates the mechanical behavior of lattice structures created from AlSi10Mg, which were produced using the laser beam powder bed fusion (LB-PBF) process. Specifically, their behavior under pure compressive loading has been numerically and experimentally investigated using ten different configurations. Experimental methods and finite element analysis (FEA) were used to investigate the behavior of body-centered cubic (BCC) lattice structures, specifically examining the effects of tapering the struts by varying their diameters at the endpoints ($d_{\mathrm{end}}$) and midpoints ($d_{\mathrm{mid}}$), as well as altering the height of the joint nodes (h). The unit cells were designed with varying parameters in such a way that $d_{\mathrm{end}}$ is changed at three levels, while $d_{\mathrm{mid}}$ and h are changed at two levels. Significant differences in Young’s modulus, yield strength, and ultimate compressive strength between the various specimen configurations were observed both experimentally and numerically. The FEA underestimated the Young’s modulus corresponding to the configurations with thinner struts in comparison to the higher values found experimentally. Conversely, the FEA overestimated the Young’s modulus of those configurations with larger strut diameters with respect to the experimentally determined values. Additionally, the proposed FE method consistently underestimated the yield strength relative to the experimental values, with notable discrepancies in specific configurations.

Laser based-powder bed fusion (LB-PBF) enables fast, efficient, and cost-effective production of high-performing products. While advanced functionalities are often derived from geometric complexity, the capability to tailor material properties also offers significant opportunities for technical innovation across many fields. This study explores the optimization of the LB-PBF process parameters for producing Ti6Al4V titanium alloy parts with controlled porosity. To this end, cuboid and lamellar samples were fabricated by systematically varying laser power, hatch distance, and layer thickness according to a full factorial Design of Experiments, and the resulting specimens were thoroughly characterized by analyzing envelope porosity, surface roughness and waviness, surface morphology, and surface area. A selection of specimens was further examined using small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS) to investigate the atomic structure and nanometric porosity of the material. The results demonstrated the possibility to finely control the porosity and surface characteristics of Ti6Al4V within specific LB-PBF process ranges. The pores were found to be mostly closed even for thin walls, while the surface roughness was recognized as the primary factor impacting the surface area. The lamellar samples obtained by exposing single scan tracks showed nearly an order-of-magnitude increase in both surface area and pore volume, thereby laying the groundwork for the production of parts with optimized porosity.