The investigation of quickly-evolving flow patterns in high-pressure and high-temperature flow rigs is crucial due to inherent hazards. There is a dire need for a high-speed, non-intrusive imaging technique to identify characteristic flow phenomena to alleviate these hazards. Electrical Impedance Tomography (EIT) enables reconstruction of the admittivity distribution of the flowing medium(s), facilitating the characterisation of its/their flow. The requirement for images at high framerates led to simultaneous voltage excitations over electrodes on the periphery of the flow associated to Frequency Division Multiplexing (FDM), doped ONe Excitation for Simultaneous High-speed Operation Tomography (ONE-SHOT) method. In previous studies, we have demonstrated the possibility of the full implementation of simultaneous excitations and measurements strategies for EIT, which maximise the number of measurements for 16 electrodes. This article presents the details of the proposed method and the signal generation/acquisition firmware based on a Field Programmable Gate Array (FPGA) data acquisition system focusing on hardware and software integration and the signal processing involved in realising the ONE-SHOT operation of the EIT. It is shown that the simultaneously generated signals are successfully discriminated and used for image reconstruction, at a rate up to 3906 frames per second (fps). The associated signalto-noise ratio varies in the 55.6 dB–69.1 dB range, depending on the generated frequency in the range of 3.906 kHz–468.7 kHz.
Electrical capacitance tomography (ECT) has been used in flow regime identification studies. Usage of raw measurements for direct time series analysis of the raw ECT data removes the need for image processing, leading to easier and faster recognition of flow regimes with non-invasive ECT sensor arrays. Based on raw ECT data, a simple algorithm that can be implemented online and provide a priori knowledge of the flow regimes is presented in this paper. In the approach proposed by us, the time series of each inter-electrode normalized capacitance measurements are taken over a suitable duration. Four mathematical operations are considered for data reduction: averaging, computation of standard deviation (SD), and high-pass and low-pass filtering. Eigenvalues of the matrices have been used for recognition of spatial features, free of artefacts caused by rotations. At this stage, the methodology categorizing flowing into stratified smooth, stratified wavy, annular, slug, or plug regimes has been tested with a significant data set of measurements of fully developed air-water flows in horizontal 56-mm diameter pipe. For selected flow regimes, four criteria, based on eigenvalues of matrices formed by raw data from the array of sensors, are tested and validated using both experimental and adequate numerical models of the sensor arrays. Based on the results presented in this paper, the approach using “frame-by-frame” time series analysis is capable of giving valuable process insight using non-intrusive sensing techniques and can be easily adapted to other sensing modalities.
The investigation of quickly-evolving flow patterns in high-pressure and high-temperature flow rigs requires the use of a high-speed and non-intrusive imaging technique. Electrical Impedance Tomography (EIT) allows reconstructing the admittivity distribution characterizing a flow from the knowledge of currents and voltages on its periphery. The need for images at high frame rates leads to the strategy of simultaneous multi-frequency voltage excitations and simultaneous current measurements, which are discriminated using fast Fourier transforms. The present study introduces the theory for a 16-electrode simultaneous EIT system, which is then built based on a field programmable gate array data acquisition system. An analysis of the propagation of uncertainties through the measurement process is investigated, and experimental results with fifteen simultaneous signals are presented. It is shown that the signals are successfully retrieved experimentally at a rate of 1953 frames per second. The associated signal-to-noise ratio varies from 59.6–69.1 dB, depending on the generated frequency. These preliminary results confirm the relevance and the feasibility of simultaneous multi-frequency excitations and measurements in EIT as a means to significantly increase the imaging rate.
Electrical impedance tomography is a non-invasive imaging technique capable of void fraction measurements of two-phase flows at high-acquisition rates. This paper presents the design features of an in-house developed prototype fast EIT system and a 16 electrodes sensor. With simplified system architecture, the voltage of the excitation signal is controlled and the current is measured. The proposed full scan data collection strategy opens up new prospects for novel flow regime identification and image reconstruction techniques currently under development. A new calibration procedure that is based on the data from full scan strategy provides reliable absolute measurements in applications, where reference measurements are not available or reliable (e.g., gas-liquid flows with drifts of liquid phase temperature). Experimental results are compared with the analytical and numerical solutions. Fundamental studies for understanding the contact impedance give insight on the influence of important parameters: excitation frequency and liquid conductivity. The quality of the measurements at different frame rates is analyzed. The repeatability at 80 kHz of the prototype highlights similar figure of merit than reported fast EIT systems. The increase in frame acquisition rate allows up to 6250 frames per second for adjacent strategy and up to 833 frames per seconds for full scan strategy.
This paper presents a concept for soft field tomographic scan of all the projections of electromagnetic waves emanating from an array of electrodes. Instead of the sequential excitation of all pairs of electrodes in the list of all projections, the new method present here consists of a single and continuous excitation. This excitation signal is the linear combination of the excitation signals in the projection set at different AC frequencies. The response to a given projection is discriminated by selecting the corresponding AC frequency component in the signal spectra of the digitally demodulated signals. The main advantage of this method is the suppression of transients after each projection, which is particularly problematic in electrical impedance tomography due to contact impedance phenomena and skin effect. The second benefit over the sequential scan method is the increased number of samples for each measurement for reduced noise sensitivity with digital demodulation. The third benefit is the increased temporal resolution in high-speed applications. The main drawback is the increased number of signal sources required (one per electrode). This paper focuses on electrical impedance tomography, based on earlier work by the authors. An experimental proof-of-concept using a simple 4-electrodes electrical impedance tomographic system is presented using simulations and laboratory data. The method presented here may be extended to other modalities (ultrasonic, microwave, optical, etc.).