Purpose: In the process of cold rolled strip, there is tight coupling between flatness control and gauge control. The variation of the roll gap caused by the change of bending force will lead to the change of rolling force. Furthermore, it can cause a deep impact on the control accuracy of strip exit thickness and exit crown. The purpose of this paper is to improve the accuracy of the bending force preset value for cold rolled strip.Design/methodology/approach: In this paper, the bending force preset control strategy with considering of rolling force was proposed for the first time and the preset objective function of bending force was established on the basis of the two-objective optimization of bending force and rolling force. Meanwhile, the multi-objective intelligent algorithm – INSGA-II – was used to solve the objective function.Findings: The proposed bending force multi-objective preset model has been tested in a 1,450 mm tandem cold rolling line. The analyzed results of field data show that the deviations of strip exit thickness and exit crown are reduced effectively by using the improved model, and at the same time, more reasonable bending force preset values are obtained, which can enhance the accuracy of flatness preset control.Originality/value: A preset model of bending force with considering flatness and gauge is proposed in this paper and the multi-objective function of bending force preset is established on the basis of the two-objective optimization of bending force and rolling force. The value lies in proposing a new decoupling method of rolling force and bending force.
A three-dimensional elastic–plastic finite element model of a six-roll cold rolling mill has been developed using the finite element software ABAQUS. The actual parameters of the rolling mill have been incorporated into the finite element model, with the working conditions applied as boundary constraints and load conditions. Subsequently, a non-symmetrical bending force is introduced to the finite element model. Through simulation calculations, this study analyzes the patterns of change in the transverse pressure of the rolling mill and roller pressure during non-symmetrical bending, as well as the variations in strip thickness, crown, edge drop, and flatness. Additionally, the regulating function of the bending force is examined. Each adjustment of 5 t in the asymmetric bending force results in an increase of approximately 0.01 mm in the thickness of the positive bending side of the strip while causing a decrease of about 0.01 mm in the thickness of the negative bending side. Therefore, the application of asymmetric bending forces proves to be effective in controlling the shape of lateral wave defects on the edges of steel strips.
1 May 2023 in Ironmaking & Steelmaking: Processes, Products and Applications
It is very complicated to study the three-dimensional deformation of metal during rolling. The conventional finite element numerical analysis method generally adopts a fixed algorithm to calculate the whole rolling process. This method consumes huge computing power and sacrifices some computing accuracy. In this paper, according to the characteristics of different rolling stages, on the basis of considering the degree of metal deformation, a particle swarm hybrid algorithm with adaptive weight-learning factor is proposed.The Zoutendijk algorithm, Rosen algorithm, Wolfe algorithm and particle swarm hybrid algorithm are used to numerically simulate the rolling transverse thickness distribution. The accuracy of the rolling model and the particle swarm hybrid algorithm are verified. The influence of work roll edge contact and asymmetric roll bending on the deformation of rolling metal is analysed based on particle swarm mixing algorithm.
3 August 2020 in The International Journal of Advanced Manufacturing Technology
Through taking the cold rolling process as the research object, the three-dimensional finite element model of the strip rolling process is established by using ANSYS/LS-DYNA software. The actual rolling product data has strong consistency with the finite element simulation results. The rolling process is dynamically simulated, and the distribution curves of important rolling parameters such as equivalent stress, control efficiency coefficient, transverse rolling pressure, lateral thickness and work roll deflection is obtained. Based on summarizing the influence of rolling parameters on rolling deformation, the research results of this paper can play an important role in the actual rolling process control. The research results have certain guiding significance for the development and optimization of the rolling control system.
In deep-sea mining operations, the seabed sediments (mud and sand) are very soft and slippery. This often causes tracked vehicles to slip and veer off course when they are driving on the seafloor. To solve the path-tracking problem for deep-sea mining vehicles, this study suggests a path-tracking controller that can adapt to the seabed environment. Firstly, it is necessary to establish a kinematic and dynamic model of the mining vehicle’s motion, analysing its seabed slippage and force application. The system has been developed on the basis of the Stanley algorithm and utilises a two-degree-of-freedom kinematic model, with lateral deviation and heading deviation acting as inputs. The establishment of fuzzy rules to adjust the gain parameter K enables the mining vehicle to adaptively modify its gain parameters according to the seabed environment and path. Secondly, a fuzzy PID controller is established and optimised to address the limitation that fuzzy PID control rules are constrained by the designer’s experience. At the same time, a relationship was established between how fast the drive wheel accelerates and the slip rate based on the dynamic model. This stops the drive wheel from slipping by limiting how fast it can go. Finally, a mechanical model of the mining vehicle was created in Recurdyn and a system model was developed in MATLAB/Simulink for joint simulation analysis. The simulation results demonstrate the efficacy of the proposed control strategy, establishing it as a reliable method for tracking the path of subsea mining vehicles.