This wind tunnel study was conducted to investigate the similarity laws involved in the reasonable simulation of the wake characteristics of a full-scale wind turbine. A 5 MW scaled wind turbine model was designed using an optimization method based on the blade element momentum (BEM) theory. Subsequently, wind tunnel tests were carried out on the geometrically similar model and the thrust-optimized model, with different yaw angles and under various upstream flow conditions. The results indicated that the wake development of the wind turbine model was closely related to the thrust forces of the wind turbine, and both kinematic and dynamic similarity laws should be observed to achieve wake characteristics that are reasonably similar to those of a full-scale wind turbine. This study investigated the aerodynamic similarity principles of small-scale wind turbine models to develop a more effective method for simulating full-scale turbine wake characteristics in wind tunnel tests. The outcomes of this study revealed the limitations of the anomalously low thrust coefficients in geometrically similar wind turbine models and present reasonable model design methodologies for small-scale wind turbine models in wind tunnel tests.
This paper investigates the twisted wind effect on a typical super-tall building (500-m-tall square prism) by conducting pressure model wind tunnel tests. Two twisted wind fields (TWFs) with maximum yaw angles of approximately 30° and 20°, respectively, near the ground level were generated in the wind tunnel using a guide vane system, and the test results of wind pressure and wind load in TWFs were compared with those obtained in conventional wind fields (CWFs) with constant wind direction along the vertical axis. In particular, the distribution of extreme cladding pressure as well as the correlation and coherence of local wind loads are discussed in detail. It was observed that the mechanism of the structural dynamic responses, such as the vortex shedding, is greatly affected by TWFs. Both the distributions of mean and extreme cladding pressures in TWFs significantly differ from those in CWFs, especially on the windward and side facades. However, in terms of the amplitudes, the extreme wind pressure and the maximum wind load in TWFs do not noticeably exceed those in CWFs. This study aims to provide useful information for the wind-resistant design of future tall buildings.
Wind tunnel test results can be influenced by various factors such as the blockage ratio and scaling ratio. These factors may introduce errors in the experimental outcomes, impacting the accuracy and reliability of the data obtained. This study quantitatively assesses consistency and identifies uncertainty sources to enhance result uniformity across various wind tunnel laboratories. This study conducted a systematic comparison between different wind tunnels in terms of rigid model pressure measurement wind tunnel experiments on the same Commonwealth Advisory Aeronautical Research Council (CAARC) standard tall building model. The study analyzes and discusses the results of mean and root-mean-square (RMS) wind pressure coefficients, peak factors, extreme wind pressure coefficients, probability density distributions, and base overturning force coefficients. The results indicated that in the open-circuit wind tunnel laboratory, the mean wind pressure coefficient is underestimated in the positive pressure region and overestimated in the negative pressure region. This is due to the static pressure which significantly decreases the streamwise direction within the test section, and the difference in static pressure is logarithmically proportional to the mean wind speed. Additionally, dynamic pressure is uniformly distributed along the test section axis. The inaccurate measurement of static pressure leads to these results. To address this issue, an indirect measurement method was employed to correct the static pressure results and reduce the error in the mean wind pressure coefficient to within 10%. Furthermore, differences in turbulence integral scale result in an error of up to 16% in the RMS wind pressure coefficient. Therefore, when conducting rigid model pressure measurement wind tunnel experiments, especially in open-circuit wind tunnel laboratories, careful consideration should be given to the influence of static pressure drop and integral length scale of turbulence.
The twisted wind flow (TWF), referring to the phenomenon of wind direction varying with height, is a common feature of atmospheric boundary layer (ABL) winds, noticeably affecting the wind-resistant structural design and the wind environment assessment. The TWF can be effectively simulated by a guide vane system in wind tunnel tests, but the proper design and configuration of the guide vanes pose a major challenge as practical experience in using such devices is still limited in the literature. To address this issue, this study aims to propose an approach to determining the optimal wind tunnel setup for TWF simulations using a numerical wind tunnel, which is a replica of its physical counterpart, using computational fluid dynamics (CFD) techniques. By analyzing the mechanisms behind guide vanes for generating TWF based on CFD results, it was found that the design must take into account three key parameters, namely, (1) the distance from the vane system to the side wall, (2) the distance from the vane system to the model test region, and (3) the separation between the vanes. Following the optimal setup obtained from the numerical wind tunnel, TWF profiles matching both the power-law and Ekman spiral models, which, respectively, reflect the ABL and wind twist characteristics, were successfully generated in the actual wind tunnel. The findings of this study provide useful information for wind tunnel tests as well as for wind-resistant structural designs and wind environment assessment.
Downbursts generate strong and transient near-surface winds that significantly influence wind flows over complex terrains. In this study, two downburst models—the impinging jet model representing the near-field region and the wall jet model representing the fully developed outflow—were experimentally investigated. The study examined the characteristics of mountain wind fields within the fully developed region, considering variations in mountain height, slope, shape, and radial position. Results show that mountain height and shape exert only minor influences on the mountain speed-up ratio, whereas slope and radial position play dominant roles: the acceleration ratio decreases with increasing radial distance and with steeper slopes. The near-surface flow is mainly affected within a vertical range of approximately 1.5 times the mountain height and a radial distance of about four times the height. By explicitly comparing the two models, this study provides the quantitative experimental relationship linking the vertical position of maximum horizontal velocity between impinging jet and wall jet flows. The comparison of mountain wind fields under equivalent positions demonstrated consistent speed-up ratios, confirming that the wall jet model can effectively reproduce the fully developed stage of downburst winds over mountainous terrain. Thus, this work offers new experimental evidence and a validated modeling framework for studying mountain wind effects under downburst conditions.