The conversion of kinetic energy from wind and solar radiation into electricity during the operation of wind and photovoltaic power plants causes practically no emissions of chemical compounds that are harmful to the environment. However, the production of their materials and components, as well as their post-use management after the end of their operation, is highly consumptive of energy and materials. For this reason, this article aims to assess the life cycle of a wind and photovoltaic power plant in the context of the sustainable development of energy systems. The objects of the research were two actual technical facilities—a 2 MW wind power plant and a 2 MW photovoltaic power plant, both located in Poland. The analysis of their life cycle was carried out on the basis of the LCA (life-cycle assessment) method, using the ReCiPe 2016 calculation procedure. The impact of the examined renewable energy systems was assessed under 22 impact categories and 3 areas of influence (i.e., human health, ecosystems, and resources), and an analysis was conducted for the results obtained as part of three compartments (i.e., air, water, and soil). The life cycle of the wind power plant was distinguished by a higher total potential negative environmental impact compared to the life cycle of the photovoltaic power plant. The highest levels of potential harmful impacts on the environment in both life cycles were recorded for areas of influence associated with negative impacts on human health. Emissions to the atmosphere accounted for over 90% of all emissions in the lifetimes of both the wind and the photovoltaic power plants. On the basis of the obtained results, guidelines were proposed for pro-ecological changes in the life cycle of materials and elements of the considered technical facilities for renewable energy sources, aimed at better implementation of the main assumptions of contemporary sustainable development (especially in the field of environmental protection).

In recent years, there has been a significant increase in the consumption of single-use packaging. Their material diversity is a significant barrier to recycling, causing overloading of landfills. Increasing negative environmental aspects have highlighted the need to develop solutions to achieve a relatively high efficiency of the bottle shaping process with the lowest possible energy consumption. The aim of the project is to try to describe the impact of this process on the state, transformation and development of the natural environment. The work concerns current issues of the impact of packaging on the natural environment. The main goal was to conduct a life cycle analysis (LCA) of beverage bottles made of polylactide. The functional unit comprised a total of 1000 pieces of PLA bottles with a capacity of 1 L. The boundary of the adopted system included the steps from the delivery of the preforms to the production plant to their correct formation in the process of forming beverage bottles. Further stages of the production process were excluded from the system, such as beverage bottling, labeling, and storage and distribution. Processes related to transport and storage of raw material were also excluded. The LCA analysis was performed using the program of the Dutch company Pre Consultants called SimaPro 8.4.0. The ReCiPe 2016 method was chosen for the interpretation of the quantity of emitted substances into the natural environment. The test results were presented graphically on bar charts and subjected to verification and interpretation.

The interest in alternative energy sources, including the use of solar radiation energy, is growing year by year. Currently, the most frequently installed photovoltaic modules are made of single-crystalline silicon solar cells (sc-Si). However, one of the latest solutions are perovskite solar cells (PSC), which are considered the future of photovoltaics. Therefore, the main objective of this research was to assess the environmental impact of the construction materials of monocrystalline and perovskite photovoltaic power plants toward their sustainable development. The research object was the construction materials and components of two 1 MW photovoltaic power plants: one based on monocrystalline modules and the other on perovskite modules. The life cycle assessment (LCA) method was used for the analyses. The IMPACT World+, IPCC and CED models were used in it. The analyses were performed separately for five sets of elements: support structures, photovoltaic panels, inverter stations, electrical installations and transformers. Two post-consumer management scenarios were adopted: storage and recycling. The life cycle of a photovoltaic power plant based on photovoltaic modules made of perovskite cells is characterized by a smaller negative impact on the environment compared to traditional power plants with monocrystalline silicon modules. Perovskites, as a construction material of photovoltaic modules, fit better into the main assumptions of sustainable development compared to cells made of monocrystalline silicon. However, it is necessary to conduct further work which aims at reducing energy and material consumption in the life cycles of photovoltaic power plants.

There is a significant demand for materials and energy throughout the manufacturing and construction of a solar power plant’s component parts. Electricity and fossil fuels are used in enormous quantities during the industrial processes in the photovoltaic power plant’s life cycle. It is then necessary to assess the energy needs, especially during production processes, to improve the efficiency of energy usage and management of natural resources from the global perspective. This will lead to a decrease in natural resource consumption and electricity demand. The main aim of this study was to assess the energy demand in the life cycle of the photovoltaic power plant and identify the most energy-intensive stages and components of this type of installation throughout its life cycle. The study of energy consumption in the whole life cycle was conducted for a 2 MW photovoltaic power plant situated in the northern region of Poland using the Life Cycle Assessment (LCA) methodology, particularly the Cumulative Energy Demand (CED) method. Two post-consumer management scenarios were investigated: recycling and landfilling. It was found that the life cycle of PV panels and the inverter station had the largest energy demand among all the components. This study revealed that, compared to recycling, the life cycle involving post-consumer management in the form of landfilling had a higher total energy demand of 4.09 × 10⁷ MJ. The results of this investigation validate the benefits of recycling. Thus, recycling ought to be commonplace to improve the environment.