The most relevant criticalities of parts produced by material extrusion additive manufacturing technologies are lower mechanical properties than standard material performances, the presence of pores caused by the manufacturing method, and issues related to the interface between layers and rods. In this context, heat treatments can be considered an effective solution for tailoring the material behavior to different application fields, especially when using precipitation hardening stainless steels. In this work, aging treatments were conducted on parts realized using three different extrusion-based processes: Atomic Diffusion Additive Manufacturing, bound metal deposition, and fused filament fabrication. Two conditions of direct aging (H900 and H1150) were considered with the aim of comparing the response of properties in the opposite conditions of peak-aged and overaged. The hardness tests revealed that H900 aging significantly influenced hardness (max increase of 52%), and porosity (− 34.3% with respect to the as-sintered condition). On the other hand, the H1150 aging decreased the hardness (− 18% max) and porosity (− 32.2% max). Substantial differences among the microstructures due to grain size and δ-ferrite were illustrated. A statistical test was included to better highlight the influence of the heat treatment on the investigated properties.
6 May 2022 in The International Journal of Advanced Manufacturing Technology
Recently, metals have been processed with fused filament fabrication (FFF) printers, in the form of mixture of metal powder and a polymeric binder. This new area of additive manufacturing is called metal-fused filament fabrication (metal FFF), and it is characterized by several advantages: low cost of manufacturing for small batches, ease of use, lower cost of energy and lower risks compared to the main metal additive manufacturing technologies. Being a novel technique, it is of great importance to understand the mechanical behaviour of the fabricated parts to reach the potential applications. In this work, the mechanical response of parts printed by metal FFF was analysed by means of digital image correlation (DIC) technique. This latter allowed to better highlight the anisotropic mechanical behaviour of the FFF parts when varying some 3D printing parameters, such as building orientation and number of wall layers and enabled a complete characterization of material useful for numerical calculation and finite element analysis. With this aim, 316L stainless steel filament and a consumer 3D printer were used for the fabrication of tensile test specimens. Three different building orientations and three different numbers of wall layers were evaluated. Results obtained from the tensile tests conducted with the DIC system highlighted the anisotropy of the strain behaviour when varying building orientation and printing strategy. More in details, flatwise and sideways configurations returned higher values of tensile strength, elongation at break and Poisson’s ratio compared to upright one, while the increase of number of wall layers, in some cases, caused a decrease of the mechanical properties.
Parts with an auxetic structure, which exhibit negative Poisson’s ratio, can be associated with a novel class of smart materials. Such interesting property has been widely explored, over the time, for different applications, i.e., medical, automotive, robotic and aeronautic field. However, the research about the design and analysis of auxetic behavior is still on the way. In this paper, a 2D re-entrant honeycomb structure was realized using material extrusion additive manufacturing technology. Two different materials, acrylonitrile butadiene styrene and carbon fiber-reinforced polyamide were adopted. The technique of digital image correlation was implemented during the tensile test to evaluate over the time and in different areas of specimens the strain behavior of the auxetic structure for both investigated materials. The measured negative Poisson’s ratio confirmed the auxetic behavior of the designed structure. The comparison between the two investigated materials showed a different trend of negative Poisson’s ratio.
Material Extrusion for Metals (MEX/M) has emerged as a cost-effective and versatile Additive Manufacturing technology (AM) for producing complex metal components. Despite its potential, parts realized via MEX/M suffer from significant limitations, primarily poor surface quality due to the intrinsic layer-wise effect from the printing deposition and selected printing conditions. Furthermore, the multi-step nature of the MEX/M process, particularly the sintering stage, can exacerbate roughness along with the printing orientation, thereby affecting part performance and limiting potential applications. In addition to surface defects, MEX parts are characterized by a high content of porosity when compared to other metal AM technologies like Powder Bed Fusion laser-based (PBF-LB) and Directed Energy Deposition laser-based (DED-LB). These defects, both on the surface and within the parts, can compromise the mechanical properties and overall quality of the final parts. In this context, the scientific community has increasingly recognized post-treatment processes as essential for simultaneously improving surface quality and enhancing bulk material properties. This review according to the PRISMA 2020 guidelines provides a comprehensive analysis of the most critical post-treatment processes applied to MEX/M parts. By critically reviewing the state of the art, this paper discusses how these treatments can effectively mitigate outer and inner defects, reduce porosity, and significantly improve mechanical performance, ultimately enabling the broader industrial adoption of MEX/M technology.