Proton Exchange Membrane Fuel Cells (PEMFCs), recognised for their high efficiency and zero emissions, represent a promising solution for automotive applications. Despite their potential, durability challenges under real-world automotive operating conditions—arising from chemical, mechanical, catalytic, and thermal degradation processes intensified by contaminants—limit their broader adoption. This review aims to systematically assess recent advancements in understanding and modelling PEMFC degradation mechanisms. The article critically evaluates experimental approaches integrated with advanced physicochemical modelling techniques, such as impedance spectroscopy, microstructural analysis, and hybrid modelling approaches, highlighting their strengths and specific limitations. Experimental studies conducted under dynamic, realistic conditions provide precise data for validating these models. The review explicitly compares physics-based, data-driven, and hybrid modelling strategies, discussing trade-offs between accuracy, computational demand, and generalizability. Key findings emphasise that hybrid models effectively balance precision with computational efficiency. Finally, the article identifies apparent research gaps. It suggests future directions, including developing degradation-resistant materials, improved simulation methodologies, and intelligent control systems to optimise PEMFC performance and enhance operational lifespan.
26 February 2024 in Journal of Thermal Analysis and Calorimetry
Despite the current growing interest in rubber composites with natural organic fillers, there is a lack of kinetic analyses that describe the decomposition of these materials during pyrolysis. For this reason, the main objective of this study was the kinetic analysis and determination of formal kinetic parameters for the pyrolytic decomposition of NR–CEL composites with different cellulose content (0, 30, 45, and 55 phr). Thermogravimetric measurements were made at heating rates of 2, 4, 6, 8, 10, and 20 °C min–1 in the temperature range of 20–600 °C. First, Friedman and KAS model-free methods were applied. Therefore, model-based methods and the model-fitting procedure were used to find the optimal multi-step kinetic model. The proposed final model consists of two parallel processes, which are kinetically independent: A → B → C and D → E → F. For each step, a kinetic triplet was calculated: the apparent activation energy, the pre-exponential factor, and the kinetic parameters of the extended empirical Prout–Tompkins model. The master plots method was used to determine the kinetic decomposition mechanism of the individual steps. It was found that step A → B has the shape of an nth-order model, step B → C mainly follows the diffusion model, the mechanism of step D → E transfers from a random scission kinetics model to an nth-order model with an increasing amount of CEL, and step E → F obeys the chain scission mechanism.
The nil-strength temperature, zero strength temperature and solidus temperature are significant parameters with respect to the processes of melting, casting and welding steels. With the use of physical tests performed on the universal plastometer Gleeble 3800 and calculations in the IDS software, the nil-strength temperatures, zero strength temperatures and solidus temperatures of nine non-alloy carbon steels have been determined. Apart from that, solidus temperatures were also calculated by the use of four equations expressing a mathematical relation of this temperature to the chemical composition of the investigated steels. The nil-strength and zero strength temperatures and the solidus temperatures decreased with increasing carbon content in the investigated steels. Much higher content of sulfur in free-cutting steel resulted in a decrease of all the temperatures investigated. The zero strength temperatures determined by calculation in the IDS software during solidification were approximately 43–85 °C higher than the nil-strength temperatures determined experimentally during heating of the investigated steels. The linear dependence of experimentally measured nil-strength temperature on the calculated zero strength temperature for the investigated steels was determined. Based on regression analyses, there were determined mathematical relations which described with high accuracy a linear dependence of the nil-strength and zero strength temperatures on the solidus temperature of the investigated steels.
1 January 2017 in Journal of Mining and Metallurgy, Section B: Metallurgy
The study deals with precise determination of phase transformation temperatures of steel. A series of experimental measurements were carried out by Differential Thermal Analysis (DTA) and Direct Thermal Analysis (TA) to obtain temperatures very close to the equilibrium temperatures. There are presented results from the high temperatures region, above 1000?C, with focus on the solidus temperatures (TS), peritectic transition (TP) and liquidus (TL) of multicomponent steels. The data obtained were verified by statistical evaluation and compared with computational thermodynamic and empirical calculations. The calculations were performed using 15 empirical equations obtained by literature research (10 for TL and 5 for TS), as well as by software InterDendritic Solidification (IDS) and Thermo-Calc (2015b, TCFE8; TC). It was verified that both thermo-analytical methods used are set correctly; the results are reproducible, comparable and close to equilibrium state.