Ján Moravec

Dr. Ján Moravec

Department of Tecnological Engineering, Faculty of Mechanical Engineering, Univesity of Zilina, Univerzitná 8215/1, 010 26 Žilina, Slovak Republic
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2018 in Metals
Verified
Journal Article
Open access
PDF file
MNMiroslav Neslušan
Miroslav Neslušan
LTLibor Trško
Libor Trško
PMPeter Minárik
Peter Minárik
JČJiří Čapek
Jiří Čapek
JBJozef Bronček
Jozef Bronček
JMJán Moravec
Ján Moravec
This paper reports about the non-destructive evaluation of surfaces after severe shot peening via the Barkhausen noise technique. Residuals stresses and the corresponding Almen intensity, as well as microstructure alterations, are correlated with the Barkhausen noise signal and its extracted features. It was found that residual stresses as well as the Barkhausen noise exhibit a valuable anisotropy. For this reason, the relationship between the Barkhausen noise and stress state is more complicated. On the other hand, the near-the-surface layer exhibits a remarkable deformation induced softening, expressed in terms of the microhardness and the corresponding crystalline size. Such an effect explains the progressive increase of the Barkhausen noise emission along with the shot-peening time. Therefore, the Barkhausen noise can be considered as a promising technique capable of distinguishing between the variable regimes of severe shoot peening.

22 December 2020 in Archives of Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
MMMiloš Mičian
Miloš Mičian
JWJ. Winczek
J. Winczek
DHD. Harmaniak
D. Harmaniak
RKR. Koňár
R. Koňár
MGM. Gucwa
M. Gucwa
JMJán Moravec
Ján Moravec
This research is focused on the analysis of heat-affected sub-zones in 2 mm thick steel S960MC samples, with the aim of observing and evaluating the mechanical properties after exposure to temperatures corresponding to individual heat-affected sub-zones. Test samples were prepared using a Gleeble 3500 thermo-mechanical simulator. The samples were heated in the range from 550°C to 1350°C and were subsequently quickly cooled. The specimens, together with the base material, were then subjected to tensile testing, impact testing, and micro-hardness measurements in the sample cross-section, as well as evaluation of their microstructure. Fracture surfaces are investigated in samples after impact testing. The heat-affected sub-zones studied indicate high sensitivity to the thermal input of welding. There is a significant decrease in tensile strength and yield strength at temperatures around 550°C.

20 March 2020 in Metals
Verified
Journal Article
Open access
PDF file
PKPetr Kawulok
Petr Kawulok
ISIvo Schindler
Ivo Schindler
BSBedřich Smetana
Bedřich Smetana
JMJán Moravec
Ján Moravec
AMAndrea Mertová
Andrea Mertová
SRStanislav Rusz
Stanislav Rusz
The nil-strength temperature, zero strength temperature and solidus temperature are significant parameters with respect to the processes of melting, casting and welding steels. With the use of physical tests performed on the universal plastometer Gleeble 3800 and calculations in the IDS software, the nil-strength temperatures, zero strength temperatures and solidus temperatures of nine non-alloy carbon steels have been determined. Apart from that, solidus temperatures were also calculated by the use of four equations expressing a mathematical relation of this temperature to the chemical composition of the investigated steels. The nil-strength and zero strength temperatures and the solidus temperatures decreased with increasing carbon content in the investigated steels. Much higher content of sulfur in free-cutting steel resulted in a decrease of all the temperatures investigated. The zero strength temperatures determined by calculation in the IDS software during solidification were approximately 43–85 °C higher than the nil-strength temperatures determined experimentally during heating of the investigated steels. The linear dependence of experimentally measured nil-strength temperature on the calculated zero strength temperature for the investigated steels was determined. Based on regression analyses, there were determined mathematical relations which described with high accuracy a linear dependence of the nil-strength and zero strength temperatures on the solidus temperature of the investigated steels.

1 September 2017 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
RPRichard Pastirčák
Richard Pastirčák
JŠJ. Ščury
J. Ščury
JMJán Moravec
Ján Moravec
The paper deals with the impact of technological parameters on the mechanical properties and microstructure in AlSi12 alloy using squeeze casting technology. The casting with crystallization under pressure was used, specifically direct squeeze casting method. The goal was to affect crystallization by pressure with a value 100 and 150 MPa. From the experiments we can conclude that operating pressure of 100 MPa is sufficient to influence the structural characteristics of the alloy AlSi12. The change in cooling rate influences the morphology of the silicon particles and intermetallic phases. A change of excluded needles to a rod-shaped geometries with significantly shorter length occurs when used gravity casting method. At a pressure of 100 MPa was increased of tensile strength on average of 20%. At a pressure of 150 MPa was increased of tensile strength on average of 30%. During the experiment it was also observed, that increasing difference between the casting temperature and the mold temperature leads to increase of mechanical properties.

27 May 2020 in Metals
Verified
Journal Article
Open access
PDF file
ASAlexander Schrek
Alexander Schrek
ABAlena Brusilová
Alena Brusilová
PŠPavol Švec
Pavol Švec
ZGZuzana Gábrišová
Zuzana Gábrišová
JMJán Moravec
Ján Moravec
This article is focused on an analysis of factors negatively affecting the tube production process of tubes made from austenitic stainless steel with a very small diameter of ϕ 0.34 mm. The analysis was concentrated on factors that affect the drawing process stability of the seam tubes where the desired final dimensions—a diameter of ϕ 0.34 mm and a wall thickness of 0.057 mm—are limiting factors. Seam tubes made from steel 1.4306 and 1.4301, from producers KT and EW with a longitudinal weld line made by tungsten inert gas (TIG) welding, were used as blanks for constituent drawing operations. It is desirable to provide sufficient inert gas flow and cooling during the formation of a weld joint in a protective atmosphere chamber. A significant temperature gradient prevents the formation of undesirable Cr23C6 carbides in the heat-affected zone (HAZ) which negatively affects the plasticity and formability of the steel and is the cause of technological fractures.

1 February 2016 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
AZAndrej Zrak
Andrej Zrak
JMJozef Meško
Jozef Meško
JMJán Moravec
Ján Moravec
RNRastislav Nigrovič
Rastislav Nigrovič
DKDalibor Kadáš
Dalibor Kadáš
The article deals with contactless thermal forming of metals. In the introduction the bending theory of components by using flame technology is described. On the basics of information obtained from the analysis of previous research a technolog...