Yucheng Ding

Dr. Yucheng Ding

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 April 2023 in Forests
Verified
Journal Article
Open access
PDF file
CYChunmei Yang
Chunmei Yang
Tongbin LiuTongbin Liu
Tongbin Liu
MYMa YaQiang
Ma YaQiang
WQWen Qu
Wen Qu
YDYucheng Ding
Yucheng Ding
WSwenlong song
wenlong song
Circumferential milling is used in wood processing, yet it generates vast quantities of dust and chips in a single pass, highlighting the need to predict chip dispersion and prevent associated hazards. This article presents findings from a theoretical and experimental analysis of chip size and kinematics of pine wood during cutting. A chip diffusion boundary surface model was established and its key parameters were determined through CCD testing. Results reveal that chip diffusion can be divided into three distinct areas based on motion state: main diffusion, random diffusion, and vortex. Notably, spindle speed and feed rate are most influential on the orthogonal diffusion angle of the main diffusion zone, whereas cutting depth most heavily impacts the top view diffusion angle. Chip scattering on the table showed an exponential increase in average chip size with sampling distance, whereas the boundary surface model accurately characterizes chip motion and demonstrates a reasonable degree of reliability, offering potential in predicting chip morphology and diffusion state. This model has important implications for wood milling practices, particularly in controlling chip dispersion.

21 September 2023 in Forests
Verified
Journal Article
Open access
PDF file
YDYucheng Ding
Yucheng Ding
TLTongbin Liu
Tongbin Liu
MYMa YaQiang
Ma YaQiang
CYChunmei Yang
Chunmei Yang
CSChangyu Shi
Changyu Shi
JZJiawei Zhang
Jiawei Zhang
Bamboo-based fiber composites, known as recombinant bamboo, have emerged as a new material in the construction and decoration industry. With its excellent mechanical and ornamental properties, recombinant bamboo is gaining popularity. However, its high hardness and abrasion resistance pose challenges in the milling process. To address this, we conducted an experimental study to investigate the milling machinability of recombinant bamboo. We studied the impact of various factors—fiber angle, feed rate, and spindle speed—on the tangential and normal roughness of milled surfaces. Our findings indicated that increasing the spindle speed within an acceptable range can effectively mitigate issues such as carbonization and endface cracking on a milled surface. Additionally, we developed a prediction model to assess the probability of end splitting in recombinant bamboo. This research aimed to enhance the milling quality of recombinant bamboo, improve control over surface roughness, reduce the likelihood of end splitting, and, ultimately, expand application possibilities.

12 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YDYucheng Ding
Yucheng Ding
STShaolin Tan
Shaolin Tan
ZLZhihao Liu
Zhihao Liu
Tongbin LiuTongbin Liu
Tongbin Liu
YMYaqiang Ma
Yaqiang Ma
CYChunmei Yang
Chunmei Yang
Due to their outstanding properties, bamboo-based fiber composites are gaining significant traction in the fields of construction and decoration. Among the crucial process steps in their production, hot pressing stands out as a pivotal one. Temperature, being a key parameter in hot pressing, and its stability of control exert a profound impact on the finished mechanical properties and associated indices of bamboo-based fiber composites. In this investigation, we introduce an active disturbance rejection control (ADRC) methodology specifically tailored for the hot-pressing temperature of bamboo-based fiber composites. A mathematical model encompassing the motor, steam regulating valve, and, ultimately, the hot-pressing temperature is formulated, with the transfer functions at each level being precisely determined through parameter identification techniques. The simulation outcomes reveal that in the absence of signal interference, sinusoidal signal interference, or random signal interference, the ADRC method outperforms the traditional PID algorithm in the realm of hot-pressing temperature control for bamboo-based fiber composites. This approach effectively reduces the temperature fluctuations of the PID algorithm, thereby averting issues such as premature curing or board bursting. In summary, this study holds significant implications for enhancing the mechanical properties of bamboo-based fiber composites.

31 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YDYucheng Ding
Yucheng Ding
JZJiawei Zhang
Jiawei Zhang
FMFanwei Meng
Fanwei Meng
STShaolin Tan
Shaolin Tan
QXQinguo Xu
Qinguo Xu
WYWenji Yu
Wenji Yu
In the hot press process of high-performance bamboo-based fiber composites, there is a highly nonlinear relationship between the production parameters of hot press and the quality parameters of the finished boards. Consequently, it is challenging to accurately predict the quality of the boards based on the given production parameters, and it is equally difficult to preset the production parameters to achieve the desired board quality. The current approach relies on manual experience, which may result in subpar board quality and material waste. To address these issues, this paper proposes a bi-directional prediction model based on cHGWO-SCA-SVR, using the collaboration-based hybrid GWO-SCA optimizer to optimize the relevant parameters of the SVR, and then accurately predicting the production parameters and the quality of the finished boards in both directions. Finally the cHGWO-SCA-SVR prediction model achieves an average R2 of 0.9591 for the forward prediction model and lower MAE and MSE values compared to other models; for the reverse prediction model, it attains an average R2 of 0.9553 and lower MAE and MSE values compared to other models. The results demonstrate the superiority of the cHGWO-SCA-SVR prediction model in comparison with other existing models, proving its significance in guiding the production of high-performance bamboo-based fiber composites by hot compression.

27 April 2023 in Research Square
Verified
Preprint
Open access
PDF file
CYChunmei Yang
Chunmei Yang
TLTongbin Liu
Tongbin Liu
YMYaqiang Ma
Yaqiang Ma
ZZZanbin Zhu
Zanbin Zhu
JYJie Yan
Jie Yan
YDYucheng Ding
Yucheng Ding
Poplar fiber mass is a non-uniform medium that is composed of discrete microelements making it an imperative raw material in the production of ultra-thin high-density wood fiberboards. Preheating, therefore, becomes a crucial process in producing ultra-thin boards from poplar fiber masses. This study aims to investigate the thermal conductivity properties of wood fiber pellets with the objective of guiding the process parameters in the preheating section.Basic size and composition of poplar fiber masses were observed using an optical microscope. Measured parameters such as bark content and stacking density were combined with observations to establish the heat transfer unit of poplar fiber masses which were then used to develop a one-dimensional equivalent heat transfer model.The steady-state images of the surface layer of poplar fiber masses were captured under different parameters using infrared thermography. The results indicated that the relationships between thickness, density, and moisture content were negatively correlated with surface layer temperature, while the relationships between bottom heating temperature and surface layer temperature were positively correlated. From these findings, the surface layer temperature of poplar fiber mass was derived, and equivalent thermal conductivity as well as convective heat transfer coefficients were solved.Simulation results showed that the average error of the equivalent heat transfer model of poplar fiber mass was 1.584 indicating that the model is usable. This study contributes to efficient simulation of steady-state heat transfer in wood fiber masses, and could be useful in guiding decision-making processes in the preheating section of ultra-thin high-density fiberboard production.

13 May 2026 in Forests
Verified
Journal Article
Open access
PDF file
JHJINJIN HE
JINJIN HE
YDYucheng Ding
Yucheng Ding
ZWZuxin Wang
Zuxin Wang
WYWenxu Yue
Wenxu Yue
The hot-pressing process for reconstituted bamboo suffers from issues such as insufficient process monitoring, scattered quality data, difficulties in quality traceability, and a lack of intuitive on-site management. This paper designs and implements a digital twin quality monitoring system tailored for the hot-pressing process of reconstituted bamboo. The system adopts an overall architecture combining a data acquisition layer, a business logic layer, and a display and interaction layer. It collects key data—such as on-site hot-pressing temperature, pressure, displacement, and equipment operating status—via PLCs and industrial communication interfaces. Based on Spring Boot and MySQL, the system handles data reception, storage, processing, and interface publishing. It integrates web pages and Unity 3D interfaces to enable basic information management, quality traceability, hot-pressing temperature monitoring, retrieval of prediction results, equipment status display, and operational data visualization. The system was deployed and validated at the enterprise’s hot-pressing production site. Test results indicate that the system continuously recorded hot-pressing process data for 2040s; the average synchronization delay between the physical end and the virtual model was 520 ms, with a maximum synchronization delay of 1360 ms and a 95th percentile synchronization delay of 910 ms, meeting the requirements for second-level monitoring and visual display of the hot-pressing process. Field application results demonstrate that the system can stably support data acquisition, quality information management, retrieval of predictive results, and digital visualization for the hot-pressing process of reconstituted bamboo, providing systematic support for quality monitoring, process traceability, and digital management of the hot-pressing process.