Fangyi You

Prof. Dr. Fangyi You


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 December 2018 in Materials
Verified
Journal Article
Open access
PDF file
QDQiulian Dai
Qiulian Dai
CLCan-Bin Luo
Can-Bin Luo
FYFangyi You
Fangyi You
Laser cladded WC/Fe coatings have the advantages of low cost and high abrasion wear resistance. However, cracks always appear in WC/Fe coatings, which limits their industrial application. In this paper, the co-effects of the re-melting process, heat treatments, and amount of Co element on the cracking susceptibility, microstructures, and mechanical properties of WC/Fe laser cladding coatings were studied. Experimental results show that re-melting process is helpful to improve the surface quality of the coating and to reduce the cracking susceptibility. The hardness of the coating decreases slightly but distributes more uniformly. Cracks in the coating can be inhibited effectively by preheating the substrate to 250 °C and maintaining the temperature during the laser cladding process, as well as applying an annealing treatment at 300 °C for 1 h. Heat treatment also results in a slight decrease in the hardness. Crack initiation cannot be restrained completely by applying the above two methods when laser cladding a big area of coating. On the basis of the above two methods, addition of Co element to the coating can further improve its toughness and decrease the crack susceptibility. Crack-free WC/Fe coating can be manufactured when 8% Co is added, and its wear resistance is much better than that of the hardened medium steel, especially when the wear time is long.

16 January 2021 in Complexity
Verified
Journal Article
Open access
PDF file
FYFangyi You
Fangyi You
WZWang Zhou
Wang Zhou
XWXuan Wang
Xuan Wang
QDQiulian Dai
Qiulian Dai
The performance of the grinding wheel demonstrably affects the machining efficiency and the quality of the workpiece. Therefore, it is essential to evaluate the wear of the wheel and then operate the dressing or replacement in time. The wear procession of the wheel was monitored and evaluated systematically in this paper. A surface grinding experiment was performed by using an alumina wheel to grind the workpiece made of Cr12. The grinding force and the grinding temperature were monitored and measured while the wheel grinds the workpiece. The surface topography of the wheel was also being observed. The distribution of the gray value of pixels in the image of the wheel surface was analyzed by the method of the histogram. Processing of the binary image of the wheel was performed after determining the gray threshold of the gray value. Then, the blockading and the wearing area on the grinding wheel were calculated. Moreover, the relation of the projection area of a single abrasive derived from theory and derived by image recognition was studied. The results of the grinding experiment show that wheel performance degradation occurs when the material removal volume reaches 210 mm3/mm. At this time, the ratio of blockage area on the grinding wheel reaches 13.4%. The percentage of the wearing area is 9.5%. The method of image recognition combined with grinding temperature is workable to realize monitoring and evaluating the wear of wheels on site without unloading them.

8 October 2022 in Machines
Verified
Journal Article
Open access
PDF file
QDQiulian Dai
Qiulian Dai
LLLianhong Liu
Lianhong Liu
FYFangyi You
Fangyi You
CLCanbin Luo
Canbin Luo
Laser cladding coatings generally need a follow-up grinding process to acquire the desired dimensional accuracy and surface roughness. In this paper, grinding experimental studies were set up to investigate the grinding performance of iron-based matrix composite coatings (WC/Fe with in situ and ex situ WC particles), using two types of grinding wheels. The influence of grinding parameters such as the cut depth, wheel speed and type of grinding wheel on grinding forces, force ratio, specific energy, surface roughness and the surface appearance of the two coatings was studied. The forming mechanism of the subsurface damages on the two ground coatings was discussed. Experimental results revealed that there were obvious differences between the two coatings in grinding forces, surface roughness and morphology, especially in the subsurface damages. These were attributed to their difference in size and the distribution of the WC particles, as well as their different mechanical properties.

1 January 2020 in Advanced Composites Letters
Verified
Journal Article
Open access
PDF file
FYFangyi You
Fangyi You
JLJin Li
Jin Li
HCHuzi Cui
Huzi Cui
QDQiulian Dai
Qiulian Dai
Bone drilling is a standard procedure in medicine mainly for internal fixation with a gripper plate. Drilling bone generates much heat, then the heat causes the temperature of bone to rise, nearby the borehole rapidly, while drilling. Studies indicated that the bone would irreversibly be damaged after being heated up to 47°C for 60 s. Hence, it is vitally important to control the drilling temperature of bone. Two different models of the tibia for drilling simulation were established with ABAQUS software based on finite element analysis in this article. The first model is an approximate ideal model of the tibia with fluid in the bone cavity. And the other one is a tubular tibia without fluid in the bone cavity, and a pair of thermocouples is embedded to match the experimental condition when measuring the drilling temperature. The distribution of heat on the bone and the highest drilling temperature were revealed by simulation, and the influences of drilling parameters on drilling temperature of bone were also explored by variance analysis. The results show that the maximum drilling temperature increases with an increase in the diameter of bit and spindle speed. The drilling temperature also increases as the feed rate increase, but the effect of feed rate on drilling temperature is not as significant as that of spindle speed. The drilling temperatures of two models were obtained by the finite element method. The maximum temperature of model 1 is taken as the benchmark. The temperature of model 2 takes as the experimental result. A formula for modifying the experimental temperature to actual value was derived. Then predicted temperature of model 1 could be achieved to obtain the optimized drilling parameters.

2 April 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RZRenhe Zhao
Renhe Zhao
DHDongqi He
Dongqi He
FYFangyi You
Fangyi You
The “insecurity of the network” characterizes each agent as being remotely controlled through unreliable network channels. In such an insecure network, the output signal can be altered through carefully designed adversarial attacks to produce erroneous results. To address this, this paper proposes a neural network (NN) adaptive secure control scheme for cyber-physical systems (CPSs) via attack reconstruction strategies, where the attack reconstruction strategy serves as the solution to the NNs estimation problem on the insecurity of the network. Consequently, by introducing a novel error transformation, an NN-adaptive secure control method is formulated as the framework of backstepping. Based on the Lyapunov stability theory and defined error transformation, it is proven that the above secure control process reaches the expected trajectory, and all the signals are bounded in closed-loop systems. Finally, its effectiveness is verified via a simulation of attitude control of two-joint robots.

1 January 2020 in Advanced Composites Letters
Verified
Journal Article
Open access
PDF file
XWXuan Wang
Xuan Wang
FYFangyi You
Fangyi You
JHJian Hong
Jian Hong
WZWang Zhou
Wang Zhou
A device for measuring the depth of the borehole base on the magnetic grid during orthopedic surgery is proposed in this article. It consists of a magnetic grid, winding sleeve, two Hall sensors, and control circuitry. The magnetic grid comprises permanent magnets and coil windings. The device fixes on the electric hand drill and works during the surgical operation. An axial pressure keeps the shaft end of the magnetic grid in contact with the surface of the bone or the plate steadily during the electric handheld drilling of the bone. The pressure is an electromagnetic force generated by the interaction between the permanent magnets and the coil windings. The force should be large enough to support the weight of the magnetic grid and a low fluctuation is maintained. The larger the device, the higher the electromagnetic force will be generated. The electromagnetic force is simulated and obtained with the software of Maxwell. The factors that influence the force were the permanent magnet, and the others are the length of permanent magnet and the turns on the coil. The results of orthogonal simulation show that the primary factor is the diameter of the permanent magnet. The optimized parameters include the following: the diameter of the magnet is 7 mm, length of each permanent magnet is 5 mm, and the turns on the coil are 80. Then the pressure force range is approximately 0.485–0.716 N, and the variance of the force is 0.137.