Qiulian Dai

Dr. Qiulian Dai


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 December 2018 in Materials
Verified
Journal Article
Open access
PDF file
QDQiulian Dai
Qiulian Dai
CLCan-Bin Luo
Can-Bin Luo
FYFangyi You
Fangyi You
Laser cladded WC/Fe coatings have the advantages of low cost and high abrasion wear resistance. However, cracks always appear in WC/Fe coatings, which limits their industrial application. In this paper, the co-effects of the re-melting process, heat treatments, and amount of Co element on the cracking susceptibility, microstructures, and mechanical properties of WC/Fe laser cladding coatings were studied. Experimental results show that re-melting process is helpful to improve the surface quality of the coating and to reduce the cracking susceptibility. The hardness of the coating decreases slightly but distributes more uniformly. Cracks in the coating can be inhibited effectively by preheating the substrate to 250 °C and maintaining the temperature during the laser cladding process, as well as applying an annealing treatment at 300 °C for 1 h. Heat treatment also results in a slight decrease in the hardness. Crack initiation cannot be restrained completely by applying the above two methods when laser cladding a big area of coating. On the basis of the above two methods, addition of Co element to the coating can further improve its toughness and decrease the crack susceptibility. Crack-free WC/Fe coating can be manufactured when 8% Co is added, and its wear resistance is much better than that of the hardened medium steel, especially when the wear time is long.

16 January 2021 in Complexity
Verified
Journal Article
Open access
PDF file
FYFangyi You
Fangyi You
WZWang Zhou
Wang Zhou
XWXuan Wang
Xuan Wang
QDQiulian Dai
Qiulian Dai
The performance of the grinding wheel demonstrably affects the machining efficiency and the quality of the workpiece. Therefore, it is essential to evaluate the wear of the wheel and then operate the dressing or replacement in time. The wear procession of the wheel was monitored and evaluated systematically in this paper. A surface grinding experiment was performed by using an alumina wheel to grind the workpiece made of Cr12. The grinding force and the grinding temperature were monitored and measured while the wheel grinds the workpiece. The surface topography of the wheel was also being observed. The distribution of the gray value of pixels in the image of the wheel surface was analyzed by the method of the histogram. Processing of the binary image of the wheel was performed after determining the gray threshold of the gray value. Then, the blockading and the wearing area on the grinding wheel were calculated. Moreover, the relation of the projection area of a single abrasive derived from theory and derived by image recognition was studied. The results of the grinding experiment show that wheel performance degradation occurs when the material removal volume reaches 210 mm3/mm. At this time, the ratio of blockage area on the grinding wheel reaches 13.4%. The percentage of the wearing area is 9.5%. The method of image recognition combined with grinding temperature is workable to realize monitoring and evaluating the wear of wheels on site without unloading them.

8 October 2022 in Machines
Verified
Journal Article
Open access
PDF file
QDQiulian Dai
Qiulian Dai
LLLianhong Liu
Lianhong Liu
FYFangyi You
Fangyi You
CLCanbin Luo
Canbin Luo
Laser cladding coatings generally need a follow-up grinding process to acquire the desired dimensional accuracy and surface roughness. In this paper, grinding experimental studies were set up to investigate the grinding performance of iron-based matrix composite coatings (WC/Fe with in situ and ex situ WC particles), using two types of grinding wheels. The influence of grinding parameters such as the cut depth, wheel speed and type of grinding wheel on grinding forces, force ratio, specific energy, surface roughness and the surface appearance of the two coatings was studied. The forming mechanism of the subsurface damages on the two ground coatings was discussed. Experimental results revealed that there were obvious differences between the two coatings in grinding forces, surface roughness and morphology, especially in the subsurface damages. These were attributed to their difference in size and the distribution of the WC particles, as well as their different mechanical properties.