Bimetallic composites have a wide range of application prospects in various industries. Different bonding temperatures, as one of the influencing factors, directly affect the bonding effectiveness as well as the performance and application of the materials. Using metallurgical bonding techniques ensures a strong bond at the interface of bimetallic materials, resulting in high-quality composite pipe billets. This paper describes an Incoloy825/P110 steel bimetal composite material made by the solid–liquid composite method. By utilizing ProCAST 14.5 software for simulation and deriving theoretical formulas, an initial range of temperatures for bimetallic preparation has been tentatively determined. And this temperature range will be utilized for on-site experiments to prepare bimetallic samples. After the preparation process is completed, samples will be selected. The influence of the external mold temperature on the interface bonding of Incoloy825/P110 steel solid–liquid composite material is studied using an ultra-depth three-dimensional morphology microscope and a scanning electron microscope. Through research, the optimal preheating temperature range for the solid–liquid composite outer mold of Incoloy825/P110 bimetallic composite material has been determined. The casting temperature of the inner mold has a significant impact on the interface bonding of this bimetal composite material. As the casting temperature of the inner mold increases, the interface thickness gradually increases. At lower temperatures, the interface thickness is lower and the bonding is poorer. At higher temperatures, melting may occur, leading to coarse grains at the interface. When the temperatures of the inner and outer molds are within a certain range, a new phase appears at the interface. Indeed, it increases the strength of the interface bonding. Due to co-melting of the bimetal near the interface, element migration occurs, resulting in increased Ni and Cr content at the interface and enhanced corrosion resistance.

The utilization of 20CrNiMo/Incoloy 825 composite materials as high-pressure pipe manifold steel can not only improve the strength and hardness of the steel, but also improve its corrosion resistance. However, research on the heat treatment of 20CrNiMo/Incoloy 825 composite materials is still scarce. Thus, the aim of this study was to investigate the influence of solid solution treatment on the microstructure and properties of 20CrNiMo/Incoloy 825 composite materials. Firstly, the composite materials were subjected to solid solution treatment at temperatures ranging from 850 to 1100 °C with varied holding times of 1 h, 4 h, and 6 h. Microstructural analysis revealed that the solid solution treatment temperature had a more pronounced effect than the treatment time on the interface decarburization layer, carburization layer, and grain size. It was observed that the carburized layer thickness decreased while the decarburized layer thickness increased with an increase in the solid solution treatment temperature, oil cooling was found to enhance the hardness of the base layer of the composite materials, and the size of the original austenite grains of 20CrNiMo steel and Incoloy 825 increased with an increase in the solid solution treatment temperature. Secondly, the tensile properties, microhardness, and fracture morphology were evaluated after the composite materials underwent solid solution treatment at temperatures between 950 °C and 1100 °C for 1 h. The results indicated that increasing the solution temperature initially led to an increase in tensile strength and elongation after fracture, followed by a decrease; furthermore, the hardness of Incoloy 825 exhibited a declining trend, while the hardness of 20CrNiMo first decreased then increased. Thirdly, the shear properties and interfacial element diffusion of the composite materials were analyzed following solid solution treatment in a temperature range of 950 °C to 1100 °C for 1 h. The findings demonstrated that higher solid solution treatment temperatures induced full diffusion of Cr, Ni, and Fe atoms at the interface and softened the matrix, leading to an increase in the thickness of the diffusion layer and toughening of the composite interface. Therefore, the shear strength increased with an increase in the solid solution treatment temperature. Finally, the optimal solid solution treatment process for 20CrNiMo/Incoloy 825 composite materials was determined to be 1050 °C/1 h oil cooling, following which the composite materials had good comprehensive mechanical properties.

This paper is focused on the rolling finite element simulation and experimental study of 20CrNiMo/Incoloy 825 composite materials. Firstly, single-pass rolling finite element simulations of the composite materials were conducted. The effects of rolling pass reduction and rolling speed on the warpage, interface strain difference, and stress of the 20CrNiMo/Incoloy 825 composite materials were evaluated, highlighting an ideal first-pass reduction of 30% and a rolling speed of 0.117 m/s. Based on these results, rolling finite element simulations under total reduction–pass conditions of 65%–3 passes, 75%–4 passes, and 85%–5 passes were conducted on 20CrNiMo/Incoloy 825 composite materials. The rolling process was found to be optimal for a total reduction of 85%–5 passes based on the ratio of the vertical compressive stress experienced by the Incoloy 825-side metal to the yield strength of Incoloy 825 at 1150 °C. Based on the results of single- and multi-pass finite element simulation experiments, microstructural observations and interface analyses were then conducted on the 20CrNiMo/Incoloy 825 composite materials after rolling. The bonding interface of the composite materials was found to be undulating, indicating good composite effects. In addition, Cr, Ni, and Fe at the interface of the composite materials exhibited a steep gradient of change, indicating trace element diffusion with a distance of 8.27 μm in the 20CrNiMo/Incoloy 825 composite materials. Finally, the interfacial bonding mechanism of the 20CrNiMo/Incoloy 825 composite materials was studied, and the results indicate that this mechanism is based on a combination of diffusion and recrystallization bonding mechanisms.