Present work proposes the substitution of traditional food stabilizers from the hydrocolloids of algae. Hydrocolloids from Nostoc commune and Nostoc sphaericum were extracted, characterized by infrared spectroscopy, and modelled their rheological behavior. The dried extract samples were dried by lyophilization and hot air and diluted in water at concentrations of 0.15% and 0.25% and lastly stored at different temperatures (7 – 80 °C). The infrared indicated C – O – C vibrations corresponding to the glucose cycle (1020 cm-1) and C = O of carboxyl groups (1950 cm-1) are proper of hydrocolloids. Rheological models of Bingham, Ostwald and Herschel-Bulkley confirmed that the Nostoc coomune species presents a higher coefficient of plastic viscosity (η) and coefficient of consistency (k) than Nostoc commune; the freeze drying method had a positive influence and significant on these results (p < 0.05). Likewise, the hydrocolloid samples were diluted under nectar conditions (12 °Brix and 4.5 pH) taking carboxymethyl cellulose (CMC) as a control, finding that there is less influence of temperature on the consistency index of hydrocolloids in the order of Nostoc sphericum < Nostoc commune < CMC. It is concluded that the application of hydrocolloids of the genus nosctoc can be used as additives in the preparation of nectar, maintaining their rheological properties.

Andean lupin (Lupinus mutabilis) oil is rich in monounsaturated (54.2%) and polyunsaturated (28.5%) fatty acids but has a ω-3:ω-6 ratio (1:9.2) above the recommended values for human health. Sacha inchi (Plukenetia volubilis) oil presents a high polyunsaturated fatty acid content (linolenic 47.2% and linoleic 34.7%), along a ω-3:ω-6 ratio (1:0.74) good for human consumption. The objective of this research was to study the physico-chemical properties and oxidative stability of tarwi and sacha inchi oil blends (1:4, 1:3, 1:1, 3:1 and 4:1 w:w) with suitable ω-3:ω-6 ratios. All blends showed ω-3:ω-6 ratios between 1:0.8 and 1:1.9, acceptable from a nutritional point of view, and high total tocopherols’ content (1834–688 mg/kg), thanks to sacha inchi. The oxidative stability index (OSI) of the mixtures by the Rancimat method at 120 °C ranged from 0.46 to 8.80 h. The shelf-life of 1:1 tarwi/sacha inchi oil blend was 1.26 years; its entropy (−17.43 J/mol), enthalpy (107.04 kJ/mol), activation energy (110.24 kJ/mol) and Gibbs energy (113.76 kJ/mol) suggest low oxidation reaction rates and good stability. Hence, balanced blends of tarwi/sacha inchi oils can achieve optimal nutritional properties and enhanced shelf-life.

Bread is a staple food in many countries of the world. The objective of this work was to include chia seeds (2-5%) in mixtures of wheat flour (71.5-81.5%), quinoa (5-10%) and cañihua (10-15%) to obtain the bread of mold. The flours were characterized by their rheological properties by means of amylography, farinography and extensography tests. The formulations allowed to increase the protein content (1.10 - 1.87%), fiber (0.45 - 3.35%) and reduce the carbohydrate content (2.95 - 10.7%) in mold which also underwent texture, color and sensory analysis. With the latter it was revealed that the highest scores regarding appearance, flavor, odor, texture and color were produced by including 2% of chia seeds in mixtures of quinoa flour (7.5%), cañihua (15%) and wheat (75.5%) (p<0.05).

The development of beverages with functional potential and maximum sensory acceptability are priorities for the food industry. This study investigated the effect of orange juice (OJ), lemon juice (LJ) and ginger juice (GJ) concentrations on overall acceptability (OA), total phenic compounds (TPC) and vitamin C (VC). The experimental design used was simplex-centroid mixtures, and maximization was achieved using response surface methodology (RSM). The bioactive content of TPC and VC was measured using the Folin–Ciocalteu method and the dichlorophenol indophenol method, respectively; sensory evaluation was conducted with 100 panelists on a continuous scale acceptability primer (0–10 points). The RSM results indicated that the optimum formulation was obtained with: OJ = 79.8 mL, LJ = 5.7 mL and GJ = 4.37 mL, yielding maximum values of OA = 6.81 points, TPC = 14.64 mg GAE/100 g and VC = 32.3 mg/mL. The optimized beverage presented a free radical scavenging capacity of 65.72% (DPPH method). The regression models were validated and significantly (p < 0.05) predicted sensory acceptability, total phenolic compounds and vitamin C content. The development of this beverage and its potential application in the food industry is attractive due to its high sensory acceptability and bioactive content.

In light of the environmental impact of disposable products made from petroleum-based plastics, this study focused on developing biodegradable foam trays made from a starch (PS) derived from potato waste and beer malt flour (BMBF). The objective of this study was to evaluate the effect of the concentration of BMBF on the physical and mechanical properties of potato starch-based foam trays prepared by the thermoforming process at temperatures of 150 °C (upper plate) and 145 °C (lower plate) for 5 min and 40 s. The results showed that increasing the BMBF concentration from 0 to 40% reduced the moisture content from 4.68% to 3.42%, increased the thickness from 2.63 cm to 4.77 cm, and decreased the density from 0.28 g.cm⁻³ to 0.15 g.cm⁻³. Meanwhile, the water absorption capacity increased from 38.7% to 69.7%. In terms of mechanical properties, increasing the BMBF concentration in the PS foam tray resulted in a decrease in hardness from 5.61 N to 2.87 N, a decrease in tensile strength from 2.92 MPa to 0.85 MPa, and a decrease in elongation from 1.42% to 0.59%. Meanwhile, fracturability increased from 2.04 mm to 3.68 mm. FTIR analysis revealed interactions between BMBF and PS in the composite foam tray. Thermogravimetric analysis (TGA) showed two thermal events: one between 20.96 °C and 172.89 °C, and another between 189.14 °C and 517.69 °C, with weight losses of 5.53% and 74.23%, leaving an ash residue of 20.24%. Differential calorimetry analysis (DSC) showed a glass transition at 152.88 °C and a melting at 185.94 °C, with an enthalpy of fusion of 74.11 J.g⁻¹. Higher concentrations of BMBF (>10%) decreased the water resistance, mechanical strength, and flexibility of the PS foam trays. Therefore, a formulation of 90% PS and 10% BMBF was better for producing a foam tray with improved mechanical properties and water resistance, which could be used as a sustainable alternative to conventional single-use plastic.