To lower the introduction and maintenance costs of autonomous power supplies for driving Internet-of-things (IoT) devices, we have developed low-cost Fe–Al–Si-based thermoelectric (FAST) materials and power generation modules. Our development approach combines computational science, experiments, mapping measurements, and machine learning (ML). FAST materials have a good balance of mechanical properties and excellent chemical stability, superior to that of conventional Bi–Te-based materials. However, it remains challenging to enhance the power factor (PF) and lower the thermal conductivity of FAST materials to develop reliable power generation devices. This forum paper describes the current status of materials development based on experiments and ML with limited data, together with power generation module fabrication related to FAST materials with a view to commercialization. Combining bulk combinatorial methods with diffusion couple and mapping measurements could accelerate the search to enhance PF for FAST materials. We report that ML prediction is a powerful tool for finding unexpected off-stoichiometric compositions of the Fe–Al–Si system and dopant concentrations of a fourth element to enhance the PF, i.e., Co substitution for Fe atoms in FAST materials.
15 October 2020 in ACS Applied Materials & Interfaces
The microstructures and Seebeck coefficients of thermoelectric alloys in the pseudo-ternary PbTe–Ag2Te–Sb2Te3 system were examined using samples that were compositionally graded by unidirectional solidification by the Bridgman method and diffusion couples. At compositions near the middle of the pseudo-binary PbTe–AgSbTe2 line, a compositionally modulated microstructure has been found. From diffusion couple experiments, it is found that the PbTe–AgSbTe2 system exhibits a miscibility gap at low temperatures while it forms a complete solid solution at high temperatures; the critical temperature is between 400 °C and 450 °C. The modulated microstructure originates from the decomposition of the high-temperature solid solution during cooling. Scanning Seebeck coefficient measurement on these samples covers a wide compositional space of the pseudo-ternary system. The Seebeck coefficient transitions from positive values at AgSbTe2-rich compositions to negative values at PbTe-rich compositions on the pseudo-binary PbTe–AgSbTe2 line. Composition-graded samples prepared by the Bridgman method are thus useful to investigate thermoelectric materials in multi-component systems.
A 0.35 /spl mu/m ECL-CMOS technology has been developed to achieve high speed and high density LSIs for mainframe computers. A high speed bipolar transistor with cutoff frequency f/sub T/ of 30 GHz and a 30 /spl mu/m/sup 2/ 6T-CMOS memory cell with a trench isolation are introduced onto an SOI substrate. This technology has been applied to a 40 ps, 120 K gate logic LSI and a 1 ns, 2.3 Mbit SRAM with 50 K gate array.
To investigate the relationship between microstructure, chemical composition, and thermoelectric properties, we have applied graded temperature heat treatments to recently developed τ1-Al2Fe3Si3-based thermoelectric (FAST) materials formed by a peritectic reaction. We investigated microstructures, chemical compositions, and Seebeck coefficients as continuous functions of heat treatment temperature. The τ1 phase can become p- and n-type semiconductors without doping by changing the Al/Si ratio. The Seebeck coefficient was maximized, exceeding |S| > 140 μVK−1 for both p- and n-type materials, by heat treatment at 1173 K for 24 h through microstructural optimization. These results show that combining the graded temperature heat treatments and spatial mapping measurements of thermoelectric properties gives effective routes to determine the suitable heat treatment temperature for materials with multiphase microstructure.
The sintered diffusion multiple (SDM) method, which has been developed in our research group, has been applied to determine the entire composition range of the CrMnFeCoNi high-entropy alloy stereoscopically and continuously over nearly the entire range. The samples were prepared by sintering mixed elemental powders and were annealed at 970 °C or 800 °C. Several hundreds of thousands of points were analyzed at random within the samples for chemical compositions using electron probe microanalysis. With the assumption that ideally, only chemical compositions of existing phases at the temperature of annealing are obtained, the compositional data thus obtained were analyzed to estimate the phase boundaries of the high-entropy phase, including the Cantor alloy composition, assuming local equilibrium within the samples. The analysis includes the determination of point densities and their slopes in the space of chemical composition. The results are shown in the tetrahedral compositional space, with vertices for the Cr, Mn, and Fe atomic fractions and the sum of the Co and Ni fractions. One of the features found in this work is that the high-entropy phase exhibits a wide compositional range in the Fe-CrMnCoNi direction. The estimated phase boundary compositions are found to be in good agreement, within an error range 3 at.%, with those obtained using samples prepared by the conventional method, where the samples with uniform compositions are equilibrated by annealing, and the compositions of their existing phases are analyzed using EPMA. Thus, the sintered diffusion multiple method is effective in providing an overview of the quinary phase diagrams.