Liquid spraying is widely used in industry, medicine, ecology, etc. At the same time, there is significant interest in highly dispersed aerosols, and there are cases where it is necessary to increase the dispersity of liquid droplets in a non-contact manner and/or droplets already suspended in the air. Ultrasound is used to enhance the dispersity of substances, such as powder particles in a liquid or for homogenizing suspensions. However, when applied to aerosols, ultrasound is typically used for particle coagulation and precipitation. This is because breaking up droplets suspended in air requires higher power input. For the first time, we investigate the processes of cavitation-induced acoustic droplet dispersion using novel ultrasound sources. The development of ultrasonic droplet fragmentation methods will expand the technological applications of aerosols, including for air and surface disinfection in enclosed spaces. Theoretically and experimentally, we determined the critical conditions for cavitation-induced droplet fragmentation. We identified the lower threshold and the saturation threshold for such fragmentation, as well as the induction time, degree of droplet deformation, dispersity, and the minimum size of newly formed droplets resulting from fragmentation. This work demonstrates significant potential for sanitation measures conducted in compliance with safety requirements, thereby contributing to the preservation and improvement of public health worldwide.
The article is devoted to the study of ultrasonic agglomeration of PM 2.5 in homogeneous and inhomogeneous ultrasonic fields. The possibility of increasing the efficiency of ultrasonic agglomeration by initiating acoustic streams in a resonant inhomogeneous ultrasonic field is shown. A inhomogeneous ultrasonic field with zones of high and low sound pressure levels formed using a bending-oscillating disk transmitter made it possible to initiate acoustic vortex-type streaming that promotes the movement of particles into the nodal areas of a standing wave and between them. Due to the formation of a inhomogeneous ultrasonic field, the efficiency of particle collection is increased: for PM 2.5, the efficiency reaches 95%; PM 1.5—92%; PM 0.5—85%. The results were obtained under the following conditions: concentration 2 × 10−2 g/m3, sound pressure level 165 dB, flow rate 6.2 m3/h. For comparison, when a homogeneous ultrasonic field is formed in the agglomeration chamber (under similar conditions), the efficiency of particle capture by inertial gas cleaning equipment does not exceed the following: for PM 2.5—89%; PM 1.5—85%; and PM 0.5—76%. The obtained research results made it possible to propose a design for an agglomeration chamber that can greatly increase the productivity of ultrasonic flow processing.
The article is devoted to investigation of energy-efficient moisture removal from capillary-porous materials. Moisture is removed by dispersion at collapse of cylindrical cavitation bubbles, formed by ultrasonic vibrations in the capillaries of the material. Mathematical model, which allowed to investigate the mechanism of moisture dispersion, has been developed. Necessity of realization of cavitation bubble full life cycle in capillary (slow growth, rapid expansion with deformation, collapse) was found. An optimal range of sound pressure levels from 150 dB (“critical level” at which dispersion of water from capillary starts) up to 170 dB (dispersion productivity growth stops due to cavitation bubbles reaching maximum size equal to diameter of capillary) was determined. It is shown that the size of the dewatered sample for maximum drying efficiency should correspond to the ultrasonic wavelength in air. Ultrasonic dispersion of liquid during drying was confirmed experimentally. It is found that for significant reduction of drying time (up to 50% and more) it is necessary to affect in the range of 165–170 dB. And the materials to be dried must be placed as particles or layers having dimensions or thicknesses corresponding to the length of the ultrasonic wave in air. The implementation of ultrasonic drying, on the example of food products (beets) provided a reduction in drying time of 1.9 times, while reducing energy costs by 1.7 times in comparison with convective drying.
15 June 2021 in Food Processing: Techniques and Technology
Introduction. Dehydration of heat-sensitive and easily oxidized food products require particular temperatures. Exposure to ultrasonic vibrations is an alternative dehydration method that presupposes moderate thermal treatment. The research objective was to identify the optimal range of sound pressure and to design a small-volume dryer. Study objects and methods. The study featured two novel ultrasonic potato dryers at t = 60 ± 1°C and a drying agent flow rate of 0.50 ± 0.03 m/s. Results and discussion. The analysis of the drying curves revealed a period of constant flow rate at a low ultrasonic exposure and its absence at a high level of exposure of ≥ 160 dB, which indicated the start of the ultrasonic dispersion process of liquid from the potato surface. The dispersion occurred due to cavitation spraying of liquid without phase transition, which significantly reduced energy consumption. As the sound pressure increased in the range from 150 to 165 dB, the drying speed increased up to 26% by 5 dB. The optimal range of the sound pressure was 160–165 dB, which optimally combined energy consumption and drying time. The research resulted in two 6 kg horizontal and vertical drum dryers that provided even ultrasonic exposure during drying. Conclusion. The convective ultrasonic potato drum dryers reduced the drying time by 44–47%
This study explores the challenges associated with dispersing disinfectant liquids for sanitizing individuals, indoor spaces, vehicles, and outdoor areas. Among the various approaches, fine aerosol sprays with a high particle surface area emerge as a particularly promising solution. Ultrasonic spraying, which leverages diverse mechanisms of ultrasound interaction with liquids, offers several distinct advantages. Notably, it enables the production of fine aerosols from liquids with a broad range of physical and chemical properties, including variations in purity, viscosity, and surface tension. This capability is especially critical for disinfectant liquids and suspensions, which often exhibit low surface tension and/or high viscosity. The article provides a comprehensive review of ultrasonic spraying methods and technologies developed by the authors’ team in recent years. It highlights innovative ultrasonic sprayers, including the latest designs, which are capable of generating aerosols with precise dispersion characteristics and high productivity from disinfectant liquids.