Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On the other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm vs. 150–500 μm for hydrodynamic spray) with high productivity (5–10 mL/s vs. 0.5 mL/min for ultrasonic spray). This approach has significant potential for modern industries and technologies.
1 December 2024 in Journal of Applied Mechanics and Technical Physics
A setup for experimental studies of the structure, shape, and size of the gas–liquid interface under ultrasonic exposure and forced aeration has been developed. It has been found that ultrasonic exposure leads to an about 1.5-fold increase in interfacial area during aeration. The ultrasound intensity has been shown to have an optimal value that provides a maximum increase in interfacial area per unit ultrasonic energy input.
This study explores the challenges associated with dispersing disinfectant liquids for sanitizing individuals, indoor spaces, vehicles, and outdoor areas. Among the various approaches, fine aerosol sprays with a high particle surface area emerge as a particularly promising solution. Ultrasonic spraying, which leverages diverse mechanisms of ultrasound interaction with liquids, offers several distinct advantages. Notably, it enables the production of fine aerosols from liquids with a broad range of physical and chemical properties, including variations in purity, viscosity, and surface tension. This capability is especially critical for disinfectant liquids and suspensions, which often exhibit low surface tension and/or high viscosity. The article provides a comprehensive review of ultrasonic spraying methods and technologies developed by the authors’ team in recent years. It highlights innovative ultrasonic sprayers, including the latest designs, which are capable of generating aerosols with precise dispersion characteristics and high productivity from disinfectant liquids.
Spraying various liquids (primarily aqueous solutions of various substances) is widely used in various technological processes. For most of them, high dispersibility and a narrow droplet size distribution are essential. Ultrasonic spraying allows these parameters to be achieved. However, the higher the dispersity of droplets produced by ultrasonic spraying, the lower the spray productivity. To solve this problem, we propose a method of multistage spraying, consisting of the generation of a large number of particles of large initial size (to ensure high productivity) and their subsequent destruction by propagation in a periodic ultrasonic field (to ensure small droplet sizes at high productivity). To experimentally determine the capabilities of this technique, a tubular emitter in the shape of a cylinder with a stepped-variable cross-section was designed. The configuration of the ultrasonic field inside the emitter (22.2 kHz; 182 dB) implements three-stage spraying (the number of sputtering stages corresponds to the number of anti-nodes along the emitter axis). The effectiveness of the proposed and developed technique, suitable for the generation of droplets smaller than 40 µm, with performance exceeding the known ultrasonic spray techniques by at least 10-fold, was confirmed in the course of the conducted research.
This study addresses the challenge of dispersing disinfectant liquids for sanitizing people, indoor spaces, vehicles, and outdoor areas. Fine aerosol sprays with a large surface area of particles are considered the most promising solution for such tasks. The study identifies shortcomings in current spraying methods and highlights the potential of ultrasonic liquid atomization for improving disinfection processes. Innovative specialized ultrasonic atomizers are introduced, capable of producing aerosols with the required droplet size and efficiency from disinfectant liquids of varying viscosities, including those containing silver nanoparticles.
Spraying various liquids (primarily aqueous solutions of various substances) is widely used in various technological processes. For most of them, high dispersibility and narrow droplet size distribution are essential. This facilitates ultrasonic spray technique. However, the higher the dispersity of droplets produced by ultrasonic spray, the lower the spray productivity. To solve this problem, we proposed a method of multistage spraying, consisting in generation of a large number of particles of large initial size (to ensure high productivity) and their subsequent destruction by propagation in a periodic ultrasonic field (to ensure small droplet sizes at high productivity). To experimentally determine the capabilities of this technique, a tubular emitter in the shape of a cylinder of stepped-variable cross-section was designed. Configuration of the ultrasonic field inside the emitter (22.2 kHz; 182 dB) implements three-stage spraying (the number of sputtering stages corresponds to the number of anti-nodes along the emitter axis). The effectiveness of proposed and developed technique suitable for generation of droplets sized less than 40 µm with performance exceeding the known ultrasonic spray techniques at least 10 times has been confirmed in the course of conducted research.