Purpose: The purpose of this paper is the presentation and research of a novel robot vision system, which uses laser dynamic triangulation, to determine three-dimensional (3D) coordinates of an observed object. The previously used physical operation principle of discontinuous scanning method is substituted by continuous method. Thereby applications become possible that were previously limited by this discretization. Design/methodology/approach: The previously used prototype No. 2, which uses stepping motors to realize a discontinuous laser scan, was substituted by the new developed prototype No. 3, which contains servomotors, to achieve a continuous laser scan. The new prototype possesses only half the width and turns out to be significantly smaller and therefore lighter than the old one. Furthermore, no transmissions are used, which reduce the systematic error of laser positioning and increase the system reliability. Findings: By using a continuous laser scan method instead of discontinuous laser scan method, dead zones in the laser scanner field can be eliminated. Thereby, also by changing the physical operation principle, the implementation of applications is allowed, which previously was limited by the fixed step size or by the object distance under observation. By using servomotors instead of stepping motors, also a significant reduced positioning time can be accomplished maintaining the relative positioning error less than 1 per cent. Originality/value: The originality is based on the substitution of the physical operation principle of discontinuous by continuous laser scan. The previously used stepping motors discretized the laser scanner field and thereby produced dead zones, where 3D coordinates cannot be detected. These stepping motors were substituted by servomotors to revoke these disadvantages and provide a continuous laser scan, where dead zones in the field of view get eliminated and the step response of the laser scanner accelerated.

Computer vision systems have demonstrated to be useful in applications of autonomous navigation, especially with the use of stereo vision systems for the three-dimensional mapping of the environment. This article presents a novel camera calibration method to improve the accuracy of stereo vision systems for three-dimensional point localization. The proposed camera calibration method uses the least square method to model the error caused by the image digitalization and the lens distortion. To obtain particular three-dimensional point coordinates, the stereo vision systems use the information of two images taken by two different cameras. Then, the system locates the two-dimensional pixel coordinates of the three-dimensional point in both images and coverts them into angles. With the obtained angles, the system finds the three-dimensional point coordinates through a triangulation process. The proposed camera calibration method is applied in the stereo vision systems, and a comparative analysis between the real and calibrated three-dimensional data points is performed to validate the improvements. Moreover, the developed method is compared with three classical calibration methods to analyze their advantages in terms of accuracy with respect to tested methods.

This paper proposes the solution of tasks set required for autonomous robotic group behavior optimization during the mission on a distributed area in a cluttered hazardous terrain. The navigation scheme uses the benefits of the original real-time technical vision system (TVS) based on a dynamic triangulation principle. The method uses TVS output data with fuzzy logic rules processing for resolution stabilization. Based on previous researches, the dynamic communication network model is modified to implement the propagation of information with a feedback method for more stable data exchange inside the robotic group. According to the comparative analysis of approximation methods, in this paper authors are proposing to use two-steps post-processing path planning aiming to get a smooth and energy-saving trajectory. The article provides a wide range of studies and computational experiment results for different scenarios for evaluation of common cloud point influence on robotic motion planning.

Purpose: The purpose of this paper is to present a novel application for a newly developed Technical Vision System (TVS), which uses a laser scanner and dynamic triangulation, to determine the vitality of agriculture vegetation. This vision system, installed on an unmanned aerial vehicle, shall measure the reflected laser energy and thereby determine the normalized differenced vegetation index. Design/methodology/approach: The newly developed TVS shall be installed on the front part of the unmanned aerial vehicle, to perform line-by-line scan in the vision system field-of-view. The TVS uses high-quality DC motors, instead of previously researched low-quality DC motors, to eliminate the existence of two mutually exclusive conditions, for exact positioning of a DC motor shaft. The use of high-quality DC motors reduces the positioning error after control. Findings: Present paper emphasizes the exact laser beam positioning in the field-of-view of a TVS. By use of high-quality instead of low-quality DC motors, a significant reduced positioning time was achieved, maintaining the relative angular position error less than 1 per cent. Best results were achieved, by realizing a quasi-continuous control, using a high pulse-width modulated duty cycle resolution and a high execution frequency of the positioning algorithm. Originality/value: The originality of present paper is represented by the novel application of the newly developed TVS in the field of agriculture. The vitality of vegetation shall be determined by measuring the reflected laser energy of a scanned agriculture zone. The paper’s main focus is on the exact laser beam positioning within the TVS field-of-view, using high-quality DC motors in closed-loop position control configuration.