The high-speed-train pantograph is a complex structure that consists of different rod-shaped and rectangular surfaces. Flow phenomena around the pantograph are complicated and can cause a large proportion of aerodynamic noise, which is one of the main aerodynamic noise sources of a high-speed train. Therefore, better understanding of aerodynamic noise characteristics is needed. In this study, the large eddy simulation (LES) coupled with the acoustic finite element method (FEM) is applied to analyze aerodynamic noise characteristics of a high-speed train with a pantograph installed on different configurations of the roof base, i.e. flush and sunken surfaces. Numerical results are presented in terms of acoustic pressure spectra and distributions of aerodynamic noise in near-field and far-field regions under up- and down-pantograph as well as flushed and sunken pantograph base conditions. The results show that the pantograph with the sunken base configuration provides better aerodynamic noise performances when compared to that with the flush base configuration. The noise induced by the down-pantograph is higher than that by the up-pantograph under the same condition under the pantograph shape and opening direction selected in this paper. The results also indicate that, in general, the directivity of the noise induced by the down-pantograph with sunken base configuration is slighter than that with the flush configuration. However, for the up-pantograph, the directivity is close to each other in Y-Z or X-Z plane whether it is under flush or sunken roof base condition. However, the sunken installation is still conducive to the noise environment on both sides of the track.

The aim of this paper is to numerically investigate cooling performances of a non-film-cooled turbine vane coated with a thermal barrier coating (TBC) at two turbulence intensities (Tu = 8.3% and 16.6%). Computational fluid dynamics (CFD) with conjugate heat transfer (CHT) analysis is used to predict the surface heat transfer coefficient, overall and TBC effectiveness, as well as internal and average temperatures under a condition of a NASA report provided by Hylton et al. [NASA CR-168015]. The following interesting phenomena are observed: (1) At each Tu, the TBC slightly dampens the heat transfer coefficient in general, and results in the quantitative increment of overall cooling effectiveness about 16–20%, but about 8% at the trailing edge (TE). (2) The protective ability of the TBC increases with Tu in many regions, that is, the leading edge (LE) and its neighborhoods on the suction side (SS), as well as the region from the LE to the front of the TE on the pressure side (PS), because the TBC causes the lower enhancement of the heat transfer coefficient in general at the higher Tu. (3) Considering the internal and average temperatures of the vane coated with two different TBCs, although the vane with the lower thermal conductivity protects more effectively, its role in the TE region reduces more significantly. (4) For both TBCs, the increment of Tu has a relatively small effect on the reduction of the average temperature of the vane.

Flutter speed of aircraft is very important and needs to be firstly specified before a certification applied for a new aircraft by airworthiness regulator to make sure that the aircraft is free from flutter in its flight envelope. By assuming geometrical and physical parameters known, the speed is usually estimated from deterministic analyses in a design stage. In practice, some parameters are finitely measured by observing, especially for the geometrical parameters, material properties and so on due to the random in nature, which causes uncertainty of information often called uncertainties. The purpose of this paper is to combine reliability analysis and optimum design of aeroelastic aircraft wing. The classical two-dimensional wing with a typical airfoil section is used as an example in this study. To quantify uncertainty in the design of flutter speed, the discrete-time aero-elastic model and worst-case scenario are applied. Furthermore, the comparison between optimum design with/without reliability is provided in this study. The results show the proposed technique leads to the flutter speed being more conservative and realizable compared with the traditional technique.

The penguin is the fastest underwater swimmer among the wing-propelled diving birds. To figure out the mechanism for its excellent swimming, the hydrodynamic performance of a penguin wing is numerically investigated using an immersed boundary method with the incompressible flow solver. This study examines the effects of feathering, flapping, and Strouhal number (St) under preset motion. Results indicate that feathering is the primary contributor to thrust generation. The change in angle of attack (AoA) can qualitatively reflect the change in lift but not thrust. Therefore, a new variable, angle of thrust (AoT, αT), is introduced to effectively reflect the change of thrust across different kinematic parameters. Optimal feathering amplitude balances the decrease in AoA and the increase in feathering angle to achieve the highest AoT and thrust. Excessive feathering amplitude degrades the leading-edge vortex to shear layers, transforms the pressure side to the suction side, and ultimately causes negative thrust (drag). Spatial analysis of the thrust shows that the outer three-fifths of the wing are the primary source of thrust, contributing 85.4% of thrust generation at optimal feathering amplitude. Flapping amplitude has little impact on the optimal feathering amplitude. The optimal feathering amplitude increases linearly with the St number in the scope of examination, leading to larger thrust but lower swimming efficiency. Thus, a dimensionless number, Stm, is introduced to describe the optimal wing motion. This work provides new insights into the propulsion mechanism of aquatic swimmers with flapping–feathering wings and helps design novel bio-inspired aquatic vehicles.