The mechanical properties of various Ti-6Al-4V alloys are influenced by their respective microstructures. This study generated an ultrafine-grain (UFG) Ti-6Al-4V alloy featuring bimodal grain distribution characteristics achieved through initial heat treatment, multi-axial forging (MF), and annealing. The study also extensively examined the evolution process of the alloy’s microstructure. By subjecting the materials to heat treatments at 900 °C with air cooling and 950 °C with air cooling, both materials were found to be consisted of primary α (αp) and transformed β (αs+β) regions with different proportions. Following MF, the sample treated at 900 °C displays a microstructure featuring UFGs of α+β surrounding larger micron-sized αp grains. On the other hand, the sample treated at 950 °C displays a microstructure distinguished by twisted αs lamellar and fragmented β grains surrounding larger micron-sized αp grains. Following annealing, no significant grain growth was observed in the sample. The geometrically necessary dislocations (GNDs) within the UFGs were eliminated, though some GNDs persisted within the αp grains. The samples undergoing the 900 °C heat treatment, MF, and subsequent annealing exhibited elevated strength (1280 MPa) and total elongation (10.7%). This investigation introduces a novel method for designing the microstructure of the Ti-6Al-4V alloy to achieve superior performance.
The RE-M-Ge systems (RE: rare earths, M: transition group elements) contain a large number of compounds with special magnetic properties. A novel compound ErMn5Ge3 was found during the investigation on the phase diagram of the Er-Mn-Ge ternary system, and its crystal structure and magnetic properties were investigated. Powder X-ray diffraction results show that ErMn5Ge3 crystallizes in an orthorhombic YNi5Si3-type structure with the space group Pnma (No. 62) and the lattice parameters of a = 13.0524(6) Å, b = 3.8853(7) Å, and c = 11.4027(4) Å. The magnetization curves and isothermal magnetization curves from 100 to 300 K were measured for ErMn5Ge3. Magnetic tests showed that the compound was weakly magnetic and had a Curie temperature of 304 K. It is believed that its magnetic properties are determined by Mn atoms, which are surrounded by a complex environment, leading to uncertainty in the direction of the magnetic moment and hence poor magnetic ordering. This uncertainty simultaneously leads to a significant separation of the ZFC and FZ curves. First-principles calculations confirm that the magnetic properties of ErMn5Ge3 are mainly provided by the Mn atoms, and its magnetic moment is calculated to be about 4.5 μB. A possible magnetic structure model with simultaneous Mn-Mn ferromagnetic/antiferromagnetic coupling is constructed based on the Mn atom spacing, which can well explain the magnetic performance of ErMn5Ge3.
A TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 multilayer coating was prepared on Nb alloys through halide activated pack cementation (HAPC) and micro-arc oxidation (MAO). The multilayer coatings were composed of a TiO2-Nb2O5-SiO2-Al2O3 outer layer, a NbSi2 middle layer and an Al-rich inner layer. The isothermal oxidation resistance of TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 multilayer coated Nb alloy was investigated at 1200 °C. Besides, the microstructure evolution and element diffusion of the composite coating were studied. The results showed that after oxidation at 1200 °C for 50 h, weight gain of TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 coating sample was 8.54 mg/cm2, which was significantly lower than the coating sample without TiO2. An improvement in the high-temperature oxidation resistance of coating with TiO2 should be ascribed to the formation of continuous and compact oxide scale on the surface.