Ziying Zhang

Dr. Ziying Zhang

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 April 2023 in Vacuum
Verified
Journal Article
Closed access
HWHuicong Wang
Huicong Wang
JLJingye Liu
Jingye Liu
SLShengyuan Lei
Shengyuan Lei
WYWeilong Yuan
Weilong Yuan
YPYicheng Pei
Yicheng Pei
ZZZiying Zhang
Ziying Zhang

21 July 2023 in Vacuum
Verified
Journal Article
Closed access
ZZZiying Zhang
Ziying Zhang
SLShengyuan Lei
Shengyuan Lei
XXXiaomeng Xie
Xiaomeng Xie
ZYZhibin Yan
Zhibin Yan
WLWeizhou Li
Weizhou Li
XZxiaolian zhao
xiaolian zhao

11 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
ZZZiying Zhang
Ziying Zhang
Weizhou LiWeizhou Li
Weizhou Li
RYRuixia Yang
Ruixia Yang
XZXiaolian Zhao
Xiaolian Zhao
HZHouan Zhang
Houan Zhang
SK5 steel is the base material used for the preparation of the wrinkle scraper, whose service life strongly affects the working efficiency and economic benefits. In this work, WC–Cr3C2–Ni coating was deposited on the SK5 steel substrate by using High-velocity air fuel spray (HVAF) and Laser cladding (LC) processes respectively, named HVAF-WC coating and LC-WC coating. The microstructure and wear resistance of both coatings were analyzed, and were compared with the substrate sample. Results showed that the coatings were adhesive well onto the substrate. More WC with fine crystals is retained in HVAF-WC coating due to low flame flow temperature, while WC of LC-WC coating is characterized by columnar crystals. The wear rate of HVAF-WC and LC-WC coating was 4.00 × 10−7 mm3/(N•m) and 3.47 × 10−6 mm3/(N•m), respectively, which was two and one orders of magnitude lower than SK5 steel with 3.54 × 10−5 mm3/Nm. HVAF-WC coating exhibited the best wear resistance because of significant fine grain strengthening, which wear mechanism is mainly dominated by abrasive wear. Thus, it was thought that HVAF-WC coating is more effective ways to improve the wear resistance of SK5 steel, comparing with LC-WC coating.

23 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
XXXiaomeng Xie
Xiaomeng Xie
EYErhui Yang
Erhui Yang
ZZZiying Zhang
Ziying Zhang
WWWu Wei
Wu Wei
DLDong Li
Dong Li
Weizhou LiWeizhou Li
Weizhou Li
To decrease energy consumption and improve the performance of micro-arc oxidation (MAO) films on 6063 Al alloy, a policy of K2TiF6 additive and electrolyte temperature control was adapted. The specific energy consumption relied on the K2TiF6 additive and more particularly on the electrolyte temperatures. Scanning electron microscopy demonstrates that electrolytes with 5 g/L K2TiF6 can effectively seal the surface pores and increase the thickness of the compact inner layer. Spectral analysis shows that the surface oxide coating consists of γ-Al2O3 phase. Following 336 h of the total immersion process, the impedance modulus of the oxidation film, prepared at 25 °C (Ti5-25), remained 1.08 × 106 Ω·cm2. Moreover, Ti5-25 has the best performance/energy-consumption ratio with a compact inner layer (2.5 ± 0.3 μm). This research found that the time of the big arc stage increased with the temperature, resulting in producing more internal defects in the film. In this work, we employ a dual-track strategy of additive and temperature providing an avenue to reduce the energy consumption of MAO on alloys.

1 January 2022 in SSRN Electronic Journal
Verified
Preprint
Open access
PDF file
YZYoucai Zhang
Youcai Zhang
SLShengyuan Lei
Shengyuan Lei
KZKang Zhang
Kang Zhang
RYRuixia Yang
Ruixia Yang
JWJiakun Wang
Jiakun Wang
ZZZiying Zhang
Ziying Zhang
A TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 multilayer coating was prepared on Nb alloys through halide activated pack cementation (HAPC) and micro-arc oxidation (MAO). The multilayer coatings were composed of a TiO2-Nb2O5-SiO2-Al2O3 outer layer, a NbSi2 middle layer and an Al-rich inner layer. The isothermal oxidation resistance of TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 multilayer coated Nb alloy was investigated at 1200 °C. Besides, the microstructure evolution and element diffusion of the composite coating were studied. The results showed that after oxidation at 1200 °C for 50 h, weight gain of TiO2-Nb2O5-SiO2-Al2O3/NbSi2/NbAl3 coating sample was 8.54 mg/cm2, which was significantly lower than the coating sample without TiO2. An improvement in the high-temperature oxidation resistance of coating with TiO2 should be ascribed to the formation of continuous and compact oxide scale on the surface.