Micro‐ and nanotexturization of surfaces can give to the parts different advanced functionalities, such as superhydrophobicity, self‐cleaning, or antibacterial capabilities. These advanced properties in combination with the biocompatibility of Liquid Silicone Rubber are an interesting approach for obtaining high‐performance medical devices. The industrial production of surface textures in polymeric materials is through the replication technique, and the best option to attain a high production rate is injection molding. Moreover, its low viscosity during processing can provide an accurate replication capacity by the easy filling by capillarity of the microtextures. An innovative replicating technique for Liquid Silicone Rubber is presented by studying the replication of different shaped textures within a diameter range of between 2 and 50 µm. The copying process consists in the overmolding of a textured polymeric inlay obtained by nanoimprint lithography. At the end of the process, a textured part is obtained, while the imprinted film remains in the mold. The injection molding parameters are optimized to increase the replication accuracy, and their effect on texture replicability is analyzed and discussed. Finally, it is shown that the textured surfaces improve their wettability behavior, which is a necessary and important characteristic in the development of biomedical devices.
20 January 2025 in The International Journal of Advanced Manufacturing Technology
This study explores the effect of the wash-out of conductive inks used during the in-mold electronic process. The influence of processing conditions and design parameters on wash-out areas during overmolding is analyzed. Using a comprehensive design of experiments approach, factors like the gate type, cavity thickness, melt temperature, injection rate, and mold temperature were evaluated. Three gating types, namely, edge, fan, and submarine, were considered. From the statistical analysis, it was demonstrated that the choice of gating type is the most important factor. Cavity thickness is the second most important factor for all three gating types. Reducing cavity thickness and raising melt temperatures generally led to a decrease in wash-out (WO), whereas the effect of injection rate varied depending on the gating method used. Adjusting mold temperature also produced favorable results, emphasizing the importance of ink-to-substrate adhesion. Simulation studies revealed the relationship between shear rate and wash-out area, underscoring the need to control injection parameters. These findings stressed the importance of meticulous design and processing to minimize wash-out defects, thus advancing in-mold electronic technology and meeting market demands for complex electronic parts.
In‐mold electronic (IME) technology enables the production of devices with 3D‐shaped electronic surfaces, where adhesives play a crucial role. Conductive adhesives are responsible for maintaining conductivity, while structural adhesives enhance functionality. Previous studies have shown that conductive adhesives influence the film deformation during the thermoforming process, impacting device functionality. Although it is presumed that structural adhesives have a similar effect, this has not been thoroughly investigated. This study compares hybridized samples using structural adhesive under different conditions to those with only conductive adhesive, analyzing stretching and thickness reduction during thermoforming. Results demonstrate improved functionality and variations in deformation. A greater amount of adhesive reduces stretching near its application, while increases as it recedes from the adhesive. However, altering the conventional adhesive disposition patterns leads to greater stretching around the adhesive. These findings indicate that the presence, amount, and disposition of structural adhesive significantly affect film behavior during processing. These factors must be carefully considered in the design of IME devices to optimize functionality.
Ultrasound micromolding (USM) is an emerging processing technology that offers advantages concerning spatial resolution, material saving, minimum time residence, minimum exposition to high temperatures and low cost. Recent advances have been focused to the point nodal tech-nology, which improves the homogeneity of the molded samples and the repeatability of the properties of processed specimens. The present work demonstrates the suitability of the modi-fied USM technology to process the biodegradable poly(3-hydroxybutyrate) (P3HB), which is a polymer that has well reported difficulties to be processed by conventional methods. Specifical-ly, conventional injection and microinjection, and USM technologies with and without point nodal configurations have been compared. Degradation studies and the evaluation of thermal and mechanical properties confirmed the successful preparation of P3HB micro-specimens, maintaining their functional integrity with minimal molecular weight loss. Exfoliated clay structures were observed for P3HB nanocomposites incorporating the C20 and C166 clays and processed by USM. The results point out the advantages of using the modified USM technology since C116 enhanced the P3HB degradation and consequently processed specimens were impos-sible to be obtained by conventional microinjection.
Ultrasound micromolding (USM) is an emerging processing technology that offers advantages with regard to spatial resolution, material savings, minimum time residence, minimum exposure to high temperatures, and low cost. Recent advances have been focused on nodal point technology, which improves the homogeneity of the molded samples and the repeatability of the properties of processed specimens. The present work demonstrates the suitability of a modified USM technology to process the biodegradable poly(3-hydroxybutyrate) (P3HB), which is a polymer that has well-reported difficulties when processed by conventional methods. Specifically, conventional injection, microinjection, and USM technologies with and without nodal point configurations have been compared. Degradation studies and the evaluation of thermal and mechanical properties confirmed the successful preparation of P3HB microspecimens, maintaining their functional integrity with minimal molecular weight loss. Exfoliated clay structures were observed for P3HB nanocomposites incorporating the C20 and C166 clays and processed by USM. The results highlight the advantages of the modified USM technology, as conventional microinjection failed to produce nanocomposites of P3HB/C116 due to the enhanced degradation caused by C116.
5 October 2026 in The International Journal of Advanced Manufacturing Technology