With the commitment to reducing environmental impact, bio-based and biodegradable aerogels may be one approach when looking for greener solutions with similar attributes to current foam-like materials. This study aimed to enhance the mechanical, thermal, and flame-retardant behavior of poly(vinyl alcohol) (PVA) aerogels by adding sodium alginate (SA) and tannic acid (TA). Aerogels were obtained by freeze-drying and post-ion crosslinking through calcium chloride (CaCl2) and boric acid (H3BO3) solutions. The incorporation of TA and SA enhanced the PVA aerogel’s mechanical properties, as shown by their high compressive specific moduli, reaching up to a six-fold increase after crosslinking and drying. The PVA/TA/SA aerogels presented a thermal conductivity of 0.043 to 0.046 W/m·K, while crosslinked ones showed higher values (0.049 to 0.060 W/m·K). Under TGA pyrolytic conditions, char layer formation reduced the thermal degradation rate of samples. After crosslinking, a seven-fold decrease in the thermal degradation rate was observed, confirming the high thermal stability of the formed foams. Regarding flammability, aerogels were tested through cone calorimetry. PVA/TA/SA aerogels showed a significant drop in the main parameters, such as the heat release rate (HRR) and the fire growth (FIGRA). The ion crosslinking resulted in a further reduction, confirming the improvement in the fire resistance of the modified compositions.
10 September 2023 in ACS Applied Polymer Materials
Lightweight materials that combine high mechanical strength, insulation, and fire resistance are of great interest to many industries. This work explores the properties of environmentally friendly alginate aerogel composites as potential sustainable alternatives to petroleum-based materials. This study analyzes the effects of two additives (tannic acid and montmorillonite clay), the orientation that results during casting, and the crosslinking of the biopolymer with glutaraldehyde on the properties of the aerogel composites. The prepared aerogels exhibited high porosities between 90% and 97% and densities in the range of 0.059–0.191 g/cm3. Crosslinking increased the density and resulted in excellent performance under loading conditions. In combination with axial orientation, Young’s modulus and yield strength reached values as high as 305 MPa·cm3/g and 7 MPa·cm3/g, respectively. Moreover, the alginate-based aerogels exhibited very low thermal conductivities, ranging from 0.038 W/m·K to 0.053 W/m·K. Compared to pristine alginate, the aerogel composites’ thermal degradation rate decreased substantially, enhancing thermal stability. Although glutaraldehyde promoted combustion, the non-crosslinked aerogel composites demonstrated high fire resistance. No flame was observed in these samples under cone calorimeter radiation, and a minuscule peak of heat release of 21 kW/m2 was emitted as a result of their highly efficient graphitization and fire suppression. The combination of properties of these bio-based aerogels demonstrates their potential as substituents for their fossil-based counterparts.
20 January 2025 in The International Journal of Advanced Manufacturing Technology
This study explores the effect of the wash-out of conductive inks used during the in-mold electronic process. The influence of processing conditions and design parameters on wash-out areas during overmolding is analyzed. Using a comprehensive design of experiments approach, factors like the gate type, cavity thickness, melt temperature, injection rate, and mold temperature were evaluated. Three gating types, namely, edge, fan, and submarine, were considered. From the statistical analysis, it was demonstrated that the choice of gating type is the most important factor. Cavity thickness is the second most important factor for all three gating types. Reducing cavity thickness and raising melt temperatures generally led to a decrease in wash-out (WO), whereas the effect of injection rate varied depending on the gating method used. Adjusting mold temperature also produced favorable results, emphasizing the importance of ink-to-substrate adhesion. Simulation studies revealed the relationship between shear rate and wash-out area, underscoring the need to control injection parameters. These findings stressed the importance of meticulous design and processing to minimize wash-out defects, thus advancing in-mold electronic technology and meeting market demands for complex electronic parts.
Some of the main properties of polysaccharide and protein-based aerogels are discussed in this chapter. The fundamentals of thermal conductivity governing the insulation properties of these materials are presented and related to the aerogel microstructure. In particular, obtaining aerogels with evenly distributed nanometric pore sizes is crucial to decreasing the thermal conductivity and to achieve super-insulation materials. Secondly, an insight into the different approaches that can be used to impart electrical conductivity or magnetic properties of bio-based aerogels is highlighted. Apart from the addition of different conductive fillers traditionally used as a second phase, the synthesis with conductive polymers and the conversion of the aerogel structure in a conductive carbon-based path enables the formation of aerogels with a wide range of electrical properties. Finally, this chapter focuses on the fire behavior of polysaccharide and protein aerogels. The basic carbohydrate structure presents a serious challenge when trying to prevent fast combustion, especially in aerogels formed from polysaccharides. However, the development of hybrid organic–inorganic systems using graphene, silicon, clay or their combination with intrinsically flame-retardant materials, such as alginates, are powerful tools in the design of aerogels with low flammability and potential industrial applications.