This work investigates the interplay of carbonization temperature and the chemical composition of carbon microfibers (CMFs), and their impact on the equilibration time and adsorption of three molecules (N2, CO2, and CH4). PAN derived CMFs were synthesized by electrospinning and calcined at three distinct temperatures (600, 700 and 800 °C), which led to samples with different textural and chemical properties assessed by FTIR, TGA/DTA, XRD, Raman, TEM, XPS, and N2 adsorption. We examine why samples calcined at low/moderate temperatures (600 and 700 °C) show an open hysteresis loop in nitrogen adsorption/desorption isotherms at −196.15 °C. The equilibrium time in adsorption measurements is nearly the same for these samples, despite their distinct chemical compositions. Increasing the equilibrium time did not allow for the closure of the hysteresis loop, but by rising the analysis temperature this was achieved. By means of the isosteric enthalpy of adsorption measurements and ab initio calculations, adsorbent/adsorbate interactions for CO2, CH4 and N2 were found to be inversely proportional to the temperature of carbonization of the samples (CMF-600 > CMF-700 > CMF-800). The enhancement of adsorbent/adsorbate interaction at lower carbonization temperatures is directly related to the presence of nitrogen and oxygen functional groups on the surface of CMFs. Nonetheless, a higher concentration of heteroatoms also causes: (i) a reduction in the adsorption capacity of CO2 and CH4 and (ii) open hysteresis loops in N2 adsorption at cryogenic temperatures. Therefore, the calcination of PAN derived microfibers at temperatures above 800 °C is recommended, which results in materials with suitable micropore volume and a low content of surface heteroatoms, leading to high CO2 uptake while keeping acceptable selectivity with regards to CH4 and moderate adsorption enthalpies.
26 May 2025 in Journal of Materials Science: Materials in Engineering
In the construction sector, diverse microorganisms have the ability to form biofilms on constructed surfaces affecting the health of the inhabitants. In this sense, diverse nanomaterials of titanium oxide (TiO2), copper oxide (CuO), and CuO/TiO2 were synthesized by the sol–gel method, Pechini method, and a mechanical synthesismethod. The influence of the thermal treatment (425–575 °C) on the formation of crystalline phases in the compounds, as well as their antibacterial activity on Escherichia coli and Staphylococcus aureus was investigated. X-ray diffraction technique(XRD) results displayed the formation of anatase, rutile, and tenorite phases on the as-synthesized samples. The Rietveld refinement analysis estimated the composition of phases, as well as the crystal size for each crystalline phase in the specimens (from ~ 16 up to ~ 165 nm). The Fourier Transform Infrared (FTIR) spectroscopy showed the characteristic M–O vibrations of the TiO2 and CuO compounds. No relevant signals of the precursors were detected. RAMAN spectroscopy confirmed the formation of anatase and rutile phases in the TiO2 nanomaterials. Scanning electron microscopy (SEM) micrographs revealed the morphology of the compounds and dynamic light scattering (DLS) and electrophoretic light scattering (ELS) analysis showed the particle sizes (from ~ 225 to ~ 750 nm) with Z-potentials between − 11 mV and − 21 mV. Nitrogen adsorption/desorption isotherms results revealed pore sizes between ~ 0.2 and ~ 12.4 nm as well as surface area values up to ~ 158 m2/g. Finally, the minimum inhibitory concentration (MIC) evaluation revealed that the compounds that CuO-based compounds exhibit good antibacterial activity, with MIC values starting at 0.625 mg/mL, and the CuO/TiO2 sample at 475 °C showed the highest efficacy at 0.312 mg/mL. These results suggest that the as-synthesized compounds could be used as disinfection agents on construction surfaces and in sick buildings, as well as they could to reduce the health risks associated with exposure to bacteria.
5 May 2022 in Journal of Chemical Technology & Biotechnology