Based on three groups of different offset voltages, a bandgap reference (BGR) and power-ON reset (POR) hybrid circuit is implemented in 65-nm CMOS. The BGR using amplifier offset voltage and current matching, and the POR using offset voltage comparison and loop settling feature, respectively, are proposed. This circuit, with low-quiescent current, not only generates a stable reference voltage independent of voltage and temperature variations, but also provides a high-robust supply-ramp-rate-tolerant power-ON/brown-out reset signal with a hysteretic window of 18-24 mV. Experimental results show that the circuit with line regulations (LNRs) of 2.63%-4.28%/V and temperature coefficients (TCs) of 22-32 ppm/°C across multiple chips has a power dissipation around 2.25 μW from a 1-V supply voltage. The circuit achieves a low noise density of 18.5 nV/√ Hz at 100-Hz offset frequency and a good figure of merit (FoM) performance. With an active core area of 0.014 mm², the circuit has fixed reset trip voltages under the supply ramp time of 0.4-100 ms.
22 March 2016 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper summarizes and compares various circuit configurations of sub-modules and RF front-ends for frequency modulated ultra-wideband (FM-UWB), and analyzes the transceiver design parameters and link margin. High-robust relaxation oscillator for subcarrier generation, low-power ring oscillators for RF FM, automatic frequency calibration (AFC) for system robustness, and preamplifier-latch based analog phase interpolation for FM demodulation, are specially clarified. A prototype 3.6-4.1 GHz FM-UWB system with bowtie antennas for short-range low-data-rate wireless data transmission is implemented in 0.18-μm CMOS. Experimental results show that the presented FM-UWB transceiver successfully generates FCC-compliant UWB spectrum and demodulates the dual-FM information, with a bit error rate (BER) of 10-6 at a distance of 60 cm and with an energy efficiency of 185 nJ/bit.
A near‐threshold low‐complexity bandgap reference (BGR) and power‐on reset (POR) hybrid circuit is implemented in 65 nm CMOS, with an ultra‐low supply voltage of 0.55 V and power consumption of 2.5 μW. The BGR employing amplifier offset voltage and current matching, and the POR based on offset voltage matching and loop settling feature, are proposed. The circuit‐level simulation results verify that the presented implementation, not only generates a stable reference voltage with the typical temperature coefficient of 120 ppm/°C and line‐regulation feature of 3.3%/V, but provides a robust reset signal with power‐on and brown‐out detection function. The proposed near‐threshold circuit has ultra‐low power supply and design complexity, both for BGR and POR modules, when compared to the reported.
2 March 2022 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
A 1.15-mW 3.75–4.25-GHz frequency-modulated ultrawideband (FM-UWB) transmitter (TX) is fabricated in 65-nm CMOS, with digitally reconfigurable subcarrier frequencies, UWB bandwidth, and radio frequency (RF) frequency band. Low-complexity submodules are utilized with significant power savings. An ultralow-current hybrid module is for bandgap reference (BGR) and power-ON reset (POR), and a single-ended crystal oscillator (XO) generates a 12-MHz clock reference. A dual-path ring voltage-controlled oscillator (VCO) conducts linear RF FM, followed by a push–pull power amplifier (PA) for 100-kb/s wireless data transmission. A differential relaxation oscillator (OSC) is for subcarrier generation, and an intermittent dual-mode frequency calibration loop ensures system robustness. Experimental results show that the presented FM-UWB TX successfully generates an Federal Communications Commission (FCC)-compliant UWB signal, with an energy efficiency of 11.5 nJ/bit and an active area of 0.21 mm 2 from a 1-V supply. The 2.25- $\mu \text{A}$ hybrid BGR and POR achieves a temperature coefficient of 32 ppm/°C, a line regulation of 2.3%/V, a supply-ramp-rate-tolerant power-ON, and brown-out function. The 40- $\mu \text{W}$ XO features a low-frequency inaccuracy of 4 ppm/V. The 40- $\mu \text{A}$ relaxation OSC provides the reconfigured two-frequency shift keying (FSK) triangular amplitude and frequency. The 2.79–5.18-GHz 0.6-mW ring VCO is capable of providing the phase noise performance of −77 dBc/Hz at the 1-MHz offset, followed by the 0.45-mW PA having the output power higher than −14 dBm and the peak power-added efficiency (PAE) of 29.6%. All these benefit low-power low-cost TX implementation, where the carrier and subcarrier frequencies are calibrated by an intermittent digital loop with omitted power dissipation.
5 September 2022 in IEEE Transactions on Microwave Theory and Techniques
A frequency-modulated ultrawideband (FM-UWB) hybrid transceiver, with a high system reuse ratio up to 90%, is fabricated in the 65-nm CMOS process for both short-range wireless communication and high-resolution radar ranging. The radio frequency (RF) front-ends (RFFEs) based on module stacking and current reuse achieve significant RF power savings of about 30% and 50% for the transmitter and the receiver (RX), respectively. The presented IF zero-crossing delay discrimination benefits a high radar resolution less than 1 cm. A multimode relaxation oscillator (OSC) for the reconfigured triangular subcarrier generation and a dual-path ring voltage-controlled oscillator (VCO) for the linear FM, stacked by a wideband push–pull power amplifier (PA), generate an FCC-compliant UWB signal. An active balun embedded low-noise amplifier (LNA) and two symmetric-detuning band-passed filters (BPFs) are stacked with the bandwidth extension to linearly demodulate the UWB FM signal. Experimental results show that the 3.75–4.25-GHz hybrid transceiver has an energy efficiency of 1.9 nJ/bit with an active area of 0.7 mm2 and a power dissipation of 1.9 mW and achieves the RX sensitivity of −71 dBm and the transmitted power of −14.1 dBm, with a bit error rate (BER) of 10−4 at a distance of 4 m under the data rate (DR) of 0.1–1.0 Mbps. The transceiver also achieves the noise figure (NF) of 4.8 dB and the phase noise of −78.6 dBc/Hz at 1-MHz offset frequency.
A 2.8 – 4.6 GHz wideband multi-core VCO with a fast start-up scheme is presented in this brief. The proposed multi-core VCO uses a successive approximation register based auto frequency control (SAR-AFC) loop with the embedded 2/3 Judge to ensure the desired output frequency. To benefit a wider application, the VCO provides radio and low frequency outputs. A prototype of the multi-core VCO is implemented in 180-nm CMOS, and consumes 20 mA from a 3.3-V supply voltage with an active area of 4.8 mm 2 . Measured results indicate that the multi-core LC VCO is capable of providing the phase noise of −120 dBc/Hz at 1-MHz offset from 4.6 GHz frequency. One of the attractive merits from the proposed LC VCO is that the response time could be saved 45% over the traditional VCO architecture.