2 March 2022 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
A 1.15-mW 3.75–4.25-GHz frequency-modulated ultrawideband (FM-UWB) transmitter (TX) is fabricated in 65-nm CMOS, with digitally reconfigurable subcarrier frequencies, UWB bandwidth, and radio frequency (RF) frequency band. Low-complexity submodules are utilized with significant power savings. An ultralow-current hybrid module is for bandgap reference (BGR) and power-ON reset (POR), and a single-ended crystal oscillator (XO) generates a 12-MHz clock reference. A dual-path ring voltage-controlled oscillator (VCO) conducts linear RF FM, followed by a push–pull power amplifier (PA) for 100-kb/s wireless data transmission. A differential relaxation oscillator (OSC) is for subcarrier generation, and an intermittent dual-mode frequency calibration loop ensures system robustness. Experimental results show that the presented FM-UWB TX successfully generates an Federal Communications Commission (FCC)-compliant UWB signal, with an energy efficiency of 11.5 nJ/bit and an active area of 0.21 mm 2 from a 1-V supply. The 2.25- $\mu \text{A}$ hybrid BGR and POR achieves a temperature coefficient of 32 ppm/°C, a line regulation of 2.3%/V, a supply-ramp-rate-tolerant power-ON, and brown-out function. The 40- $\mu \text{W}$ XO features a low-frequency inaccuracy of 4 ppm/V. The 40- $\mu \text{A}$ relaxation OSC provides the reconfigured two-frequency shift keying (FSK) triangular amplitude and frequency. The 2.79–5.18-GHz 0.6-mW ring VCO is capable of providing the phase noise performance of −77 dBc/Hz at the 1-MHz offset, followed by the 0.45-mW PA having the output power higher than −14 dBm and the peak power-added efficiency (PAE) of 29.6%. All these benefit low-power low-cost TX implementation, where the carrier and subcarrier frequencies are calibrated by an intermittent digital loop with omitted power dissipation.
4 November 2021 in IEEE Access
A 2.8 – 4.6 GHz wideband multi-core VCO with a fast start-up scheme is presented in this brief. The proposed multi-core VCO uses a successive approximation register based auto frequency control (SAR-AFC) loop with the embedded 2/3 Judge to ensure the desired output frequency. To benefit a wider application, the VCO provides radio and low frequency outputs. A prototype of the multi-core VCO is implemented in 180-nm CMOS, and consumes 20 mA from a 3.3-V supply voltage with an active area of 4.8 mm 2 . Measured results indicate that the multi-core LC VCO is capable of providing the phase noise of −120 dBc/Hz at 1-MHz offset from 4.6 GHz frequency. One of the attractive merits from the proposed LC VCO is that the response time could be saved 45% over the traditional VCO architecture.
28 May 2025 in IEEE Microwave and Wireless Technology Letters
This letter presents a broadband D-band amplifier in 250-nm indium phosphide double heterojunction bipolar transistors (InP DHBT) technology. To enhance the output power and improve efficiency, the amplifier operates at class-AB and contains two transistors in parallel. The integrated active biasing is designed to mitigate the inherent self-heating effect of bipolar transistors while also improving linearity. The use of a small resistor and an inductor between the base and bias circuity boosts the gain and overall circuit stability. According to the measured results, the proposed single-stage amplifier achieves a maximum gain of 6.2 dB with a flattened bandwidth across the D band and delivers a 40-GHz large-signal bandwidth at output power levels exceeding 6 dBm. The measured maximum $P_{\text {sat}}$ and PAE achieve 9.2 dBm and 25.2% at 130 GHz under the power dissipation of 25.1 mW within a power supply of 1.2V, respectively. The compact chip occupies $0.55\times 0.47$ mm, with an active area of 0.09 mm2. The proposed monolithic microwave integrated circuit (MMIC) achieves excellent PAE and bandwidth performance, making it possible for wireless systems exceeding 100 GHz.
2 February 2026 in Microelectronics Journal
23 August 2025 in Journal of Electronic Testing