This article proposes an LC-based spiral transmission line structure, which can effectively reduce the area of ON-chip transmission lines. The quarter-wavelength transmission line realized by this transmission line structure can be widely used in millimeter-wave circuits design. Based on the LC-based spiral transmission line structure, a 28-GHz single-pole double-throw (SPDT) switch and a 37-GHz Wilkinson power combiner are implemented with an area of only 0.028 mm² in 65-nm CMOS. Measurement results indicate that the SPDT switch has an insertion loss of less than 1.5 dB and an isolation better than 23.7 dB in the frequency range from 20 to 35 GHz. The insertion loss and the isolation of the Wilkinson power combiner at 36.9 GHz is 0.9 and 30.3 dB, respectively.
9 February 2023 in IEEE Transactions on Antennas and Propagation
Since the coexistence of microwave (MW) and millimeter-wave (MMW) technologies have become the inexorable trend of emerging wireless communication systems, the corresponding antennas are required to support two frequency bands simultaneously. However, the existing MW/MMW shared-aperture antennas are facing challenges in dealing with the interference between two bands and implementing beam steering at both bands. To address these issues, a windowed slow-wave parallel-plate waveguide (WSW-PPW) is proposed as the sharing platform, on which MW and MMW antenna elements can be flexibly arranged. WSW-PPW is implemented by embedding electromagnetic bandgap (EBG) structures into a dual-layer printed parallel-plate waveguide. At the MW band, WSW-PPW exhibits a transmission feature for feeding and also integrating MW antenna elements. At the MMW band, WSW-PPW rejects the propagation of electromagnetic waves and functions as artificial magnetic boundaries for dielectric resonator antennas which are realized by removing subarrays of EBG structures. For demonstration, an MW/MMW shared-aperture antenna is implemented by integrating a 1 × 2 MW patch array and a 1 × 8 MMW array on this platform. Steerable beams had been independently achieved at both bands. The antenna is fabricated and experimentally verified. The measured results show a reasonable agreement with simulations.
18 September 2018 in IEEE Transactions on Circuits and Systems II: Express Briefs
A fully integrated D-band transceiver front-end with on-chip frequency synthesizer is implemented in 65-nm CMOS. The transceiver front-end adopts the dual-conversion sliding-IF heterodyne architecture to relax the design difficulty of the local oscillation (LO) signal generator. The D-band signal is first down-converted via a 100-GHz LO signal and IQ down-converted via a 50-GHz quadrature LO signal in the receiver. While in the transmitter, the modulated signal is generated at 50 GHz and up-converted via a 100-GHz LO signal. The measured transmitter output power is 2.1 dBm at 150 GHz, with > 11 GHz 3-dB bandwidth. The measured results also show the cascaded gain of the receiver can be programmed from 57.4 dB to 45.6 dB with 3-dB bandwidth of 9.6 GHz to >20 GHz.
20 July 2017 in IEEE Microwave and Wireless Components Letters
A high output power 152 GHz ON–OFF keying transmitter in 65-nm CMOS is presented. The transmitter consists of a high dc-RF efficiency push–push voltage-controlled oscillator followed by a high-speed and high-gain switched-mode power amplifier. The transmitter achieves the highest output power (3 dBm) beyond 140 GHz in silicon process, with high on–off ratio (>39 dB) and high dc-RF efficiency (3.7%). The transmitter could support 10-Gb/s data rate communication with a bit-error rate of less than $10^{-12}$ .
17 March 2022 in IEEE Microwave and Wireless Components Letters
This letter presents an ultra-compact gm-boost low noise amplifier (LNA) with only one multi-coupled transformer for the first time. Implemented in 65-nm CMOS process, the proposed LNA achieves a measured peak gain of 10.5 dB with its 3-dB bandwidth ranging from 21 to 34.5 GHz and a noise figure (NF) of 2.5 dB at 28 GHz, while consuming 4-mW dc power. Based on the superior compactness of the transformer, the core area of the LNA is optimized to only $0.03~{\text {mm}}^{2}$ .
27 December 2023 in IEEE Microwave and Wireless Technology Letters
This letter presents a Ku-band 3.3-V low-noise amplifier (LNA) with a multicoupled transformer using current-reuse techniques. The multicoupled transformer combines a shunt resonator and a series resonator forming multiple resonant frequencies. Furthermore, the topology enhances the equivalent $Q$ factor of the inductors for input matching and reduces the noise factors. Wideband input matching and noise matching are realized simultaneously. Fabricated in a 65-nm CMOS process, the LNA achieves a 1.58–2.63-dB NF and a 29.6-dB power gain from 9.5 to 13.5 GHz with a 1.5-dB ripple. The LNA consumes 20 mW from a 3.3-V supply and occupies an area of 0.39 mm $^{2}$ .