Polymer-dispersed liquid crystal (PDLC) films were prepared by the ultraviolet-light-induced polymerization of photopolymerizable monomers in nematic liquid crystal/chiral dopant/thiol-acrylate reaction monomer composites. The effects of the chiral dopant and crosslinking agents on the electro-optical properties of the PDLC films were systematically investigate. While added the chiral dopant S811 into the PDLC films, the initial off-state transmittance of the films was decreased. It was found that the weight ratio among acrylate monomers, thiol monomer PETMP and the polymercaptan Capcure 3-800 showed great influence on the properties of the fabricated PDLC films because of the existence of competition between thiol-acrylate reaction and acrylate monomer polymerization reaction. While adding polymercaptans curing agent Capcure 3-800 with appropriate concentration into the PDLC system, lower driven voltage and higher contrast ratio were achieved. This made the polymer network and electro-optical properties of the PDLC films easily tunable by the introduction of the thiol monomers.

In this study, a polymer dispersed cholesteric liquid crystal (PDChLC) film obtained via a one-step fabrication technique based on photopolymerization of a thiol-acrylate reaction system was prepared and characterized for the first time. The effects of the chiral dopant, the influence of thiol monomer functionality and content on the morphology and subsequent performance of the PDChLC films were systematically investigated. It was demonstrated that the addition of a small amount of chiral dopant slightly increased the driving voltage, but decreased the off-state transmittance significantly. Furthermore, scanning electron micrographs (SEM) shown that the liquid crystal (LC) droplet size decreased at first and then increased with the increasing amount of thiol monomer functionality, while increasing the thiol content increased the LC droplet size. Correspondingly, the electro-optical switching behavior was directly dependent on LC droplet size. By tuning the raw material composition, PDChLC film with optimized electro-optical performance was prepared.

Chemical functionalization is an effective approach to address interfacial deterioration caused by environmental exposure in cellulose nanofiber (CNF)-epoxy nanocomposites. However, how functionalization affects interfacial deterioration and durability of nanocomposites in erosive environment is still lacked. In this work, the global mechanical properties and local interfacial intermolecular behavior of pristine and functionalized CNF-reinforced nanocomposites are investigated through molecular dynamics simulations. The results show that functionalization can enhance the interfacial energy barrier and debonding stress by 43% and 57%, respectively. Functionalized CNF inhibits the slippage of epoxy chains, ensuring better interfacial adhesion and efficient stress transfer between fiber and matrix. Functional groups promote the formation of interfacial bridging and topological structures and weaken the hydrogen bonding ability of water molecules, leading to stronger intermolecular adsorption effect and better interfacial integrity. The epoxy molecular configuration evolution and intermolecular interactions, caused by the functionalization of CNF in the interfacial region, enhance the interfacial erosion resistance, contributing to the durability of the nanocomposites. This study reveals the in-depth interfacial deterioration mechanism of functionalized nanocomposites under erosive environment, inspiring a novel strategy for the design of durable CNF-reinforced nanocomposites.

High-performance and cost-effective laser protection system is of crucial importance for the rapid advance of lasers in military and civilian fields leading to severe damages of human eyes and sensitive optical devices. However, it is crucially hindered by the angle-dependent protective effect and the complex preparation process. Here we demonstrate that angle-independence, good processibility, wavelength tunability, high optical density and good visibility can be effectuated simultaneously, by embedding dichroic anthraquinone dyes in a cholesteric liquid crystal matrix. More significantly, unconventional two-dimensional parabolic protection behavior is reported for the first time that in stark contrast to the existing protection systems, the overall parabolic protection behavior enables protective effect to increase with incident angles, hence providing omnibearing high-performance protection. The protective effect is controllable by dye concentration, LC cell thickness and CLC reflection efficiency, and the system can be made flexible enabling applications in flexible and even wearable protection devices. This research creates a promising avenue for the high-performance and cost-effective laser protection, and may foster the development of optical applications such as solar concentrators, car explosion-proof membrane, smart windows and polarizers.

In the harsh application environment, improving the mechanical properties of liquid crystal materials is a fundamental and important problem in the design of anti-counterfeit materials. In this paper, by a stepwise polymerization of first, photo-polymerization and subsequently thermal-polymerization, a coexistent polymer dispersed network was first constructed in cholesteric liquid crystal materials containing a photo-polymerizable system of urethane acrylate and a thermo-polymerizable system of isocyanate. Results revealed that the coexistent polymer dispersed network exhibited largely enhanced mechanical performance, and the networks obtained by different methods had different contributions to the enhancement of the peel strength and toughness of the composite films. Then an angular photochromic anti-fake label based on a coexistent polymer dispersed network with enhanced mechanical and apparent angular discoloration characteristics, suitable for practical applications, was successfully achieved.