In this paper, a transimpedance amplifier (TIA) is presented that utilizes a modified pseudo-resistor (PR) with improved robustness against temperature and process variations, enhanced linearity, and reduced parasitics. Using a biasing scheme named pseudo current mirror, the conventional dependence on absolute process parameters is reduced to a dependence on matching of alike devices. The linearity and noise performance as well as the immunity against process variations of the presented TIA are improved by the series connection of multiple PR elements. Moreover, it is shown how implementing the design in a silicon-on-insulator (SOI) technology reduces critical parasitics, which in turn enables the use of the multi-element PR in high-speed, high-gain, and low-distortion TIAs. A prototype realization in a 180-nm CMOS SOI technology achieves a tunability in transimpedance of three orders of magnitude from 1 GΩ down to 1 MΩ with corresponding bandwidths from 8 kHz to 2 MHz. By design, the contribution of shot noise is rendered negligible and the white noise floor of the prototype realization approaches the theoretical thermal noise limit, e.g., 5.5 fA/√Hz for a transimpedance of 1 GΩ and 140 fA/√Hz for 1 MΩ. Total harmonic distortion values of less than 0.1% are achieved for an input amplitude of 300 pAp-p for 1 GΩ, 4.0 nAp-p for 100 MΩ, and 40 nAp-p for 10 MΩ, and less than 1% is achieved for an input amplitude of 550 nAp-p for 1 MΩ. The presented TIA consumes an area of 0.07 mm² and dissipates a power of 9.3 mW for the opamp and a maximum power of 0.2 mW for the PR from a 1.8-V supply.
8 October 2019 in IEEE Journal of Solid-State Circuits
This article presents a dual-loop noise-coupling (NC)-assisted continuous-time (CT) sturdy multistage noise-shaping (SMASH) Δ Σ modulator (DSM), employing 1.5-bit/4-bit quantizers. The proposed SMASH can equivalently work as an overall fourth-order DSM with 4-bit internal quantization. The NC applied in this CT SMASH DSM whitens the 1.5-bit quantization noise (QN) and further reduces its in-band tone power, while a finite-impulse response (FIR) filter integrated into the outermost feedback path suppresses the out-of-band (OOB) noise power of the multibit digital-to-analog converter (DAC) input. Together, they avoid any linearization technique for the multibit DAC. Sampled at 1.2 GHz, the 28-nm CMOS experimental prototype measures a signal-to-noise-and-distortion ratio (SNDR) of 76.6 dB and a spurious-free dynamic range (SFDR) of 87.9 dB over a 50-MHz bandwidth (BW), consuming 29.2 mW from 1.2-V/1.5-V supplies and occupying an active area of 0.085 mm². It exhibits a Schreier figure-of-merit (FoM) (SNDR) of 168.9 dB.
12 December 2008 in IEEE Journal of Solid-State Circuits
This paper reports on a field-programmable analog array (FPAA) for high-frequency continuous-time analog filters. A rapid-prototyping hardware is presented, which implements a unique hexagonal lattice topology of 55 tunable Gm cells for reconfigurable instantiation of Gm-C filters in a 0.13 mum CMOS technology. The typical power dissipation is 70 mW at a 1.2 V supply. The chip structure allows intuitive mapping of Gm-C filter schematics with up to seven independent nodes, immediate download to the hardware, and evaluation on the working prototype. Implementations of first- and second-order low-pass and sixth-order bandpass filters are presented and show the feasibility of the array for frequencies up to the order of one hundred MHz.
15 August 2019 in IEEE Journal of Solid-State Circuits
The use of continuous-time delta-sigma modulators (CTDSM) as a replacement of traditional analog sensor front ends has become an increasingly popular choice. The absence of traditional sensor interface circuits, such as instrumentation amplifiers (IAs), reduces area and power consumption at the cost of robustness offered by these circuits. Selection of the integrator type in the CTDSM is a selection of the ADC properties. This article presents a current feedback CTDSM with high input impedance, wide linear operating range, and large-signal common-mode rejection as a neural recorder front end. We propose the modification of an IA for operation as an integrator in a delta-sigma modulator and the current reuse of the feedback DAC current to bias this integrator stage. Deploying the current reuse technique, the total power consumption of the modulator is reduced by 22%. The ASIC is developed in a 180-nm high-voltage CMOS technology and the analog front end achieves a dynamic range of 90 dB and a total harmonic distortion (THD) of 0.005% when configured for a full-scale input signal of 208 mVsubscriptpp. A common-mode rejection ratio (CMRR) of 90 dB is measured for a common-mode disturbance of 325 mVsubscriptpp while the analog power consumption per channel is 23 μW.
29 January 2019 in IEEE Journal of Solid-State Circuits
This paper presents a dynamic power reduction technique for incremental ΔΣ (I-ΔΣ) modulators. The technique makes use of the unequal weighting of the digital reconstruction filter. The underlying idea is that the input signal samples are not equally weighted in the higher order reconstruction filter. Thus, it is possible to increase the non-idealities of the I-ΔΣ modulator during the runtime of a single Nyquist conversion, thereby saving power. This principal idea is verified by an example design, where the input-referred noise of the first integrator is dynamically increased, which allows for improved efficiency. The proposed technique is readily applicable to every state-of-the-art I-ΔΣ modulator. Furthermore, it is shown that this property can also be used to switch a single-bit digital-to-analog converter (DAC) into a multibit DAC during runtime, thereby greatly improving the achievable signal-to-quantization-noise ratio (SQNR) without suffering from the DAC non-linearity. The prototype I-ΔΣ modulator is manufactured in a 180-nm CMOS technology and achieves a dynamic range/SNDR = 91.5/86.6 dB for a sampling rate of 200 kS/s while consuming l.l mW from a 3-V supply, while the dynamic power reduction method accounts for 30% power savings.
11 May 2021 in IEEE Journal of Solid-State Circuits
This article presents the integration of a 32-channel neuromodulation system on chip (SoC) that is developed for chronic implantation in humans. The application-specific integrated circuit (ASIC) offers low-noise recording, a state-of-the-art (SotA) neurostimulator capable of both current- and voltage-controlled stimulation with high-voltage compliance, on-chip 16-bit data digitization as well as safety features such as electrode impedance estimation and charge balancing. The chip communicates through two distinct SPI interfaces for independent command and data transfer. Thus, the developed system constitutes a fully digital, bidirectional 32-channel interface to the brain.